Fault Identification
Show/hide table
Fault Identification     | ||||
Indicator left side of GSC+     |
Fault Code on upper display     | DIAG Indicator     | Fault Type     | See Topic     |
Fault Alarm     | CID FMI (1)     | Flashing     | Active Alarm     | Troubleshooting Diagnostic Codes     |
SP1, SP2, SP3, SP4 (1) | None     | Active Alarm     | SP Fault Code - Troubleshoot     | |
AL1 thru AL15 (1) | None     | Active Alarm     | AL Fault Codes - Troubleshoot     | |
Fault Shutdown     | CID FMI     | Flashing     | Active Shutdown     | Troubleshooting Diagnostic Codes     |
SP1, SP2, SP3, SP4 | None     | Active Shutdown     | SP Fault Code - Troubleshoot     | |
AL5 thru AL15 (1) | None     | Active Alarm     | AL Fault Code - Troubleshoot     | |
Dedicated Shutdown: Flashing On Continuously     |
None     | None     | Active Alarm     | Troubleshooting Dedicated Shutdown Indicators     |
None | None     | Active Shutdown     | ||
None     | CID FMI (2)     | On Continuously     | Inactive Alarm     | Troubleshooting Diagnostic Codes     |
CID FMI (2) | On Continuously     | Inactive Shutdown     | Troubleshooting Diagnostic Codes     | |
SP1, SP2, SP3, SP4 | None     | Inactive Shutdown     | SP Fault Code - Troubleshoot     | |
AL5 through AL15 (1) | None     | Inactive Alarm     | AL Fault Code - Troubleshoot     | |
None | None     | Undetermined Shutdown     | Troubleshooting Undetermined Problems     |
Show/hide table
( 1 ) | The fault code is shown after alarm codes key is pressed. |
( 2 ) | Fault Code is stored in the fault log of the GSC+. To view the fault code, see Systems Operation, "Fault Log Viewing OP1" within the topic Service Mode. |
Show/hide table
Illustration 1 | g00614724 |
GSC+ Display Area (1) Dedicated shutdown indicators (2) Spare fault indicators (3) Fault shutdown indicator (4) Fault alarm indicator (5) Upper display (6) Lower display (7) Keypad (8) DIAG indicator |
Faults that are diagnosed by the GSC+ are shown to service personnel in the display area of the GSC+. The GSC+ uses the following information to tell service personnel about a fault: dedicated following shutdown indicators (1), fault shutdown indicator (3),, fault alarm indicator (4), "DIAG" indicator (8), upper display (5) and lower display (6). Perform the following procedure in order to identify the fault that is detected by the GSC+.
Note: The "DIAG" indicator (8) functions when diagnostic information is available from the GSC+.
- Make a note of the indicators that are functioning on the left side of the "GSC+".
- View the fault code on the upper display (5). If the fault alarm indicator (4) is FLASHING and no fault code is present on the upper display (5), press the alarm codes key in order to view the fault code.
- Note the condition of the "DIAG" indicator (8). The "DIAG" indicator will flash CONTINUOUSLY or the "DIAG" indicator will NOT flash.
- Locate the fault indicator that is functioning on Table 1.
- Go to the second column in Table 1. Find the fault code that is presently shown on the upper display (5) .
- Go to the third column in Table 1 which describes the status of "DIAG" indicator (8) .
- Read the last two columns in Table 1 in order to find the type of fault and corresponding topic within this module.
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Tools
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines General Information
3606 and 3608 Engines Engine Oil Coolers - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Sensors and Electrical Connectors
C9 Engine For Caterpillar Built Machines Engine Oil Filter Base - Install
G3304 and G3306 Engines Turbocharger
3126B Truck Engine Air Compressor - Remove and Install
3126B Truck Engine Fan Drive - Install
C9 Engine For Caterpillar Built Machines Engine Oil Filter Base - Remove
3126B Truck Engine Fan Drive - Remove
3126B Truck Engine Belt Tensioner - Remove and Install
3606 and 3608 Engines Engine Oil Coolers - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 100 FMI 2 Pressure Sensor (Engine Oil) Incorrect Signal - Test
3612 and 3616 Engines Engine Oil Coolers - Assemble
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 110 FMI 2 Temperature Sensor (Engine Coolant) Incorrect Signal - Test
3406E Generator Set Engines Safety Signs and Labels
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
3054 and 3056 Industrial and Generator Set Engines Lifter Group
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 2 Temperature Sensor (Engine Oil) Incorrect Signal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 3 Temperature Sensor (Engine Oil) Voltage Above Normal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 4 Temperature Sensor (Engine Oil) Voltage Below Normal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test