Engine Oil Coolers - Assemble
组装步骤
- 将适当的起吊设备连接到发动机机油冷却器芯 (14) 上。 发动机机油冷却器芯 (14) 的重量约为 90 kg (200 lb)。 将发动机机油冷却器芯置于支架组件 (12) 之上。 发动机机油冷却器芯 (14) 的末端至支架组件 (12) 中的第一个螺栓孔的中心线的距离 (X) 必须为 436.0 ± 1.0 mm (17.16 ± 0.04 in)。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
 | |
| 图 1 | g01292777 |
Show/hide table
 | |
| 图 2 | g00608623 |
Show/hide table
 | |
| 图 3 | g00629387 |
- 在发动机机油冷却器芯 (14) 各端上安装密封垫和阀盖 (9) 。
- 安装支架 (11) ，将发动机机油冷却器芯固定到位。
- 在支架 (11) 上安装油温调节器壳体 (13) 。
注: 较新的发动机配备带有更长出口的油温调节器壳体 (13) 。
- 在油温调节器壳体各侧上安装法兰 (3) 和软管 (5) 。
- 安装歧管 (6) 。 安装其他歧管 (10) 。
- 在歧管 (6) 上安装弯头 (7) 。
- 将适当的起吊设备连接到发动机机油冷却器芯 (4) 上。 发动机机油冷却器芯 (4) 的重量约为 45 kg (100 lb)。 在岐管 (6) 和其他岐管 (10) 上安装发动机机油冷却器芯。 安装将发动机油冷却器芯 (4) 固定入位的螺栓。
- 在发动机机油冷却器各侧上安装下列部件: 阀盖 (2), 软管 (8) 和 弯头 (1) 。
End By: 安装发动机机油冷却器。 请参阅 拆解和组装, "发动机机油冷却器 - 安装"。
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 100 FMI 2 Pressure Sensor (Engine Oil) Incorrect Signal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Fault Identification
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Tools
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines General Information
3606 and 3608 Engines Engine Oil Coolers - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Sensors and Electrical Connectors
C9 Engine For Caterpillar Built Machines Engine Oil Filter Base - Install
G3304 and G3306 Engines Turbocharger
3126B Truck Engine Air Compressor - Remove and Install
3126B Truck Engine Fan Drive - Install
C9 Engine For Caterpillar Built Machines Engine Oil Filter Base - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 110 FMI 2 Temperature Sensor (Engine Coolant) Incorrect Signal - Test
3406E Generator Set Engines Safety Signs and Labels
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
3054 and 3056 Industrial and Generator Set Engines Lifter Group
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 2 Temperature Sensor (Engine Oil) Incorrect Signal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 3 Temperature Sensor (Engine Oil) Voltage Above Normal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 4 Temperature Sensor (Engine Oil) Voltage Below Normal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
3406E Generator Set Engines Reference Material
3114, 3116, and 3126 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install