Air Screen Housing - Remove and Install
Removal Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Loosen clamps (1). Remove cover (2) and the gasket for the cover.
Show/hide table
Illustration 1 | g00635117 |
- Remove the air screen.
- Disconnect the electrical connector (not shown) from the rear of the housing.
- Loosen clamp (3) .
- Attach a suitable strap and a lifting device to the housing. The weight of the housing is approximately 35 kg (77 lb).
- Remove bolts and washers (4) that attach the housing to the lower bracket and the upper support.
- Remove the housing.
- Temporarily cover the air inlet for the turbocharger in order to prevent debris from entering the air inlet.
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the inside of the housing and the cover are clean.
- Attach a suitable strap and a lifting device to the housing. The weight of the housing is approximately 35 kg (77 lb).
- Remove the temporary cover from the air inlet for the turbocharger.
- Lift the housing into position on the air inlet of the turbocharger. Install bolts and washers (4) that attach the housing to the upper support and the lower bracket.
Show/hide table
Illustration 2 | g00635117 |
- Install clamp (3) .
- Connect the electrical connector (not shown) to the rear of the housing.
- Install the air screen into the housing.
Note: Before installing the air screen, inspect the screen for cleanliness and good condition.
- Inspect the gasket of the cover for cleanliness and good condition. Install cover (2) with the gasket. Fasten clamps (1) .
Caterpillar Information System:
C-9 Industrial Engine Engine Oil Filter Base
3114, 3116, and 3126 Engines for Caterpillar Built Machines Unit Injector - Remove
3114, 3116, and 3126 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
3003, 3013, 3014 and 3024 Industrial Engines Fuel Shutoff Solenoid - Remove and Install
C-15, C-16 and C-18 Truck Engines Engine Oil Pan - Remove and Install
3512B Marine Auxiliary Engines Crankshaft - Install
3512B Marine Auxiliary Engines Crankshaft - Remove
3512B Marine Auxiliary Engines Camshaft - Install
3512B Marine Auxiliary Engines Camshaft - Remove
3512B Marine Auxiliary Engines Crankshaft Main Bearings - Install
3116 On Highway Engines Exhaust Manifold - Remove and Install
3003, 3013, 3014 and 3024 Industrial Engines Engine Description
3512B Marine Auxiliary Engines Fumes Filter - Remove and Install
3116 On Highway Engines Crankshaft Main Bearings - Remove
3003, 3013, 3014 and 3024 Industrial Engines Engine Crankcase Breather - Clean
3406E On-Highway Engine Engine Control Module - Remove and Install
30SI Series and 34SI Series Alternator General Information
3003, 3013, 3014 and 3024 Industrial Engines Reference Material
3114, 3116, and 3126 Industrial and Generator Set Engines Safety Signs and Labels
30SI Series and 34SI Series Alternator Normal Operation
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electronic Control Module (ECM) - Flash Program
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Emergency Stopping
3003, 3013, 3014 and 3024 Industrial Engines Refill Capacities
3406E and 3456 Generator Set Engines Vibration Damper and Pulley - Remove and Install