Rotary Manifold - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1864     | Retaining ring pliers     | 1     |
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Lubricate all seals and all rings with clean hydraulic oil.
- Install spacer (7) to manifold (1) .
Show/hide table
Illustration 1 | g00683215 |
- Install six seals (5) and six rings (6) to housing (4) .
Show/hide table
Illustration 2 | g00683183 |
- Place housing (4) into position on manifold (1). If necessary, use a hydraulic press or a rubber mallet in order to seat the housing.
Show/hide table
Illustration 3 | g00683232 |
Note: Ensure that you do not damage the seals when you install the housing onto the manifold. Lubricate the seals before you attempt to install the housing.
- Install spacer (3). Use Tooling (A) to install retaining ring (2) to rotary manifold (1) .
Show/hide table
Illustration 4 | g00683173 |
End By: Install the rotary manifold. Refer to Disassembly and Assembly, "Rotary Manifold - Install" for further information.
Caterpillar Information System:
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Disassemble
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Assemble
315C Excavator Automatic Engine Speed Control (AEC)
M318 and M320 Excavators Power Train Downshift Inhibitor - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Front) - Time
988G Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Flash Program
2000/03/27 Improved Water Connection Group {1393}
3126B Engines Engine Speed - Check
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Control Valve - Remove
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Wear Plates - Remove and Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - H195
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - 180/H180s
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Test
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Control Valve - Install
315C Excavator Fine Swing Control - If Equipped
315C Excavator Hydraulic Lockout Control
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Remove - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325D and 329D Excavators Joystick Controls Alternate Patterns
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Disassemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325C and 325C L Excavator Fuel Tank Shutoff and Drain Control
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Remove
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Install
2004/09/06 Product Support Literature for Custom Product Machines {0374}