Rotary Manifold - Assemble
Assembly Procedure
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Lubricate all seals and all rings with clean hydraulic oil.
- Lubricate seals (7) with clean hydraulic oil. Install the seals to housing (5) .
Show/hide table
Illustration 1 | g00684797 |
- Lubricate seal (6) with clean hydraulic oil. Install the seal to manifold (3) with the sealing lip at the top. Ensure that the seal is properly seated against the mounting plate at the bottom of the manifold. Refer to Illustration 3 for the proper orientation of the seal.
Show/hide table
Illustration 2 | g00684795 |
Show/hide table
Illustration 3 | g00685120 |
- Place housing (5) onto the manifold. Use a soft mallet or a hydraulic press in order to seat the housing on the manifold. Use care to ensure that the seals are not damaged during assembly.
- Lubricate seal (4) with clean hydraulic oil. Install the seal to cover (2) with the sealing lip away from the cover.
Show/hide table
Illustration 4 | g00684793 |
- Place cover (2) into position on rotary manifold (3). Install two bolts (1) and the washers that secure the cover to the manifold. Tighten the bolts to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
Show/hide table
Illustration 5 | g00684791 |
End By: Install the rotary manifold. Refer to Disassembly and Assembly, "Rotary Manifold - Install" for further information.
Caterpillar Information System:
315C Excavator Automatic Engine Speed Control (AEC)
M318 and M320 Excavators Power Train Downshift Inhibitor - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Front) - Time
988G Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Flash Program
2000/03/27 Improved Water Connection Group {1393}
3126B Engines Engine Speed - Check
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Control Valve - Remove
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Wear Plates - Remove and Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - H195
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pads - Remove and Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - 160/H160s
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Disassemble
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Test
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Control Valve - Install
315C Excavator Fine Swing Control - If Equipped
315C Excavator Hydraulic Lockout Control
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Remove - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325D and 329D Excavators Joystick Controls Alternate Patterns
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Disassemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325C and 325C L Excavator Fuel Tank Shutoff and Drain Control
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Remove