Rotary Manifold - Disassemble
Disassembly Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-1864 | Retaining ring pliers | 1 |
| B | 5F-7343 | Bearing puller | 1 |
Start By:
- Remove the rotary manifold. Refer to Disassembly and Assembly, "Rotary Manifold - Remove" for further information.
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Place rotary manifold (1) on a clean work bench.
Show/hide table
 | |
| Illustration 1 | g00683169 |
- Use Tooling (A) to remove retaining ring (2) . Remove spacer (3) .
Show/hide table
 | |
| Illustration 2 | g00683173 |
- Install Tooling (B) onto housing (4). Place the assembly in a hydraulic press. Use the press to separate the housing from the manifold.
Show/hide table
 | |
| Illustration 3 | g00683182 |
- Remove six seals (5) and six rings (6) from housing (4) .
Show/hide table
 | |
| Illustration 4 | g00683183 |
- Remove spacer (7) from manifold (1) .
Show/hide table
 | |
| Illustration 5 | g00683215 |
Caterpillar Information System:
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Assemble
315C Excavator Automatic Engine Speed Control (AEC)
M318 and M320 Excavators Power Train Downshift Inhibitor - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Front) - Time
988G Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Flash Program
2000/03/27 Improved Water Connection Group {1393}
3126B Engines Engine Speed - Check
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Control Valve - Remove
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Wear Plates - Remove and Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - H195
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pressure Control Valve - 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Pads - Remove and Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Test
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Control Valve - Install
315C Excavator Fine Swing Control - If Equipped
315C Excavator Hydraulic Lockout Control
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Remove - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Install - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325D and 329D Excavators Joystick Controls Alternate Patterns
115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, 180/H180s and H195 Hydraulic Hammers Check Valve - Disassemble - 115/H115s, 120/H120s/H120Cs, 130/H130s, 140/H140s, 160/H160s, and 180/H180s
325C and 325C L Excavator Fuel Tank Shutoff and Drain Control
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Remove
313B ExcavatorEngine Supplement Engine and Main Hydraulic Pump - Install