Water Pump - Disassemble
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-2321     | 组合式拉拔器     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 1P-0510     | 冲头总成     | 1     |
开始:
- 拆下水泵。 请参阅拆解和组装, "水泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
操作已经加热的零件时要坚持戴防护手套。 |
注: 如果将水泵加热到 80 °C (176 °F),部件可以轻松地拆下。
- 拆下将水泵皮带轮固定到水泵上的四条螺栓 (1) 和垫圈。
Show/hide table
图 1 | g00610108 |
- 将水泵皮带轮 (2) 从水泵上拆下。
注: 检查水泵皮带轮的 V 形皮带槽有无磨损和损坏。 如有必要,更换水泵皮带轮。
- 利用工具 (A) 将法兰 (3) 从水泵上拆下。
注: 在要求采用压具或手锤的水泵拆解程序中使用工具 (C) 。
Show/hide table
图 2 | g00610120 |
- 利用工具 (B) 将挡圈 (4) 从水泵上拆下。
Show/hide table
图 3 | g00610127 |
- 利用压具和工具 (C) 将轴组件 (5) 从水泵组件 (6) 上拆下。
Show/hide table
图 4 | g00610140 |
- 将叶轮 (8) 从轴组件 (5) 上拆下。
注: 检查叶轮有无磨损、腐蚀和金属件之间直接接触。 如有必要,更换叶轮。
Show/hide table
图 5 | g00813948 |
- 将以下各项从轴 (9) 上拆下:
- 轴承 (10)
- 隔套 (11)
- 轴承 (12)
- 垫圈 (13)
- 轴承 (10)
- 所有部件拆下后,检查轴 (9) 是否变形。 必要时,更换轴。
- 检查密封 (14) 有无磨损和损坏。 必要时,利用工具 (C) 将密封从水泵壳上拆下。
注: 如果水泵运行中出现泄漏迹象,则更换密封。
- 利用新 O 形圈更换 O 形圈 (7) 。
Caterpillar Information System:
3126B Engines for Caterpillar Built Machines Crankshaft - Install
307B Excavator Lift Capacities
3126B Engines for Caterpillar Built Machines Crankshaft - Remove
3064 and 3066 Engines for Caterpillar Built Machines Water Pump - Install
3064 and 3066 Engines for Caterpillar Built Machines Water Pump - Remove
SR4B Generators Generator Operation
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Drift Reduction Valve (Boom) - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Drift Reduction Valve (Boom) - Remove
A13 Auger Maintenance Interval Schedule
307B Excavator Monitoring System
C-9 Engines for Caterpillar Built Machines Valve Mechanism Cover
307B Excavator Machine System Specifications Recoil Spring
3126B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
5230 Excavator Hydraulic System Power Shift Pressure - Check
3114, 3116, and 3126 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Water Pump - Assemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Oil Filter (Hydraulic, Return) - Remove
307B Excavator Machine Systems Final Drive and Travel Motor - Disassemble - Single Speed
M318 Excavator Hydraulic System Control Valve (Stick Lowering) - Test and Adjust
A13 Auger Frame Mounting Bracket - Inspect - Skid Steer Loader Only
C-9 Engines for Caterpillar Built Machines Gear Group (Front)
3126 Truck Engine Military Pistons and Connecting Rods - Remove