Gas Pressure Regulator - Disassemble
开始:
- 拆下气体压力调节器。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将气压调节器 (1) 定位在合适的台面上。
Show/hide table
图 2 g00595577 - 拧松防松螺母 (2)。
Show/hide table
一定要拧松调整螺钉。 如果不拧松调整螺钉,极大的弹簧压力就有可能造成人身伤害。
- 拧松调整螺钉。
注: 计下旋转圈数。 这样做是为了使调整螺钉能够返回到原始位置。
Show/hide table图 3 g00595580 - 卸下管组件 (4)。
- 卸下管组件 (5)。
Show/hide table
图 4 g00595582 - 卸下阀 (6)。
Show/hide table
图 5 g00595584 - 从滤芯组件 (8) 上卸下阀体 (7)。
Show/hide table
图 6 g00595587 (7) 阀体。 (9) 螺钉。 (10) 垫圈。 (11) 滤芯。 (12) 垫圈。 (13) 盖。 - 拆解滤芯组件 (8)。
Show/hide table
图 7 g00595590 - 卸下八个螺栓 (15)。
- 卸下壳体 (14)。
Show/hide table
图 8 g00595593 - 卸下垫圈 (16) 和弹簧 (17)。
Show/hide table
图 9 g00595596 - 卸下接头 (18)。
- 翻转气压调节器。
Show/hide table
图 10 g00595600 - 卸下四个螺栓 (20)。
- 卸下壳体 (19) 和垫片。 请检查垫片是否损坏。 如有必要,更换垫片。
注: 小心地将弹簧从壳体上卸下。 弹簧受压。
Show/hide table图 11 g00595603 - 卸下护圈 (21) 和弹簧 (22)。
注: 计下旋转圈数。 这样做是为了使螺纹护圈能够返回到合适位置。
Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
Show/hide table图 12 g00595605 - 从壳体 (23) 上卸下十二个螺栓 (24)。
Show/hide table
图 13 g00595743 - 将盖 (23) 连带轴和膜片一起卸下。
注: 必须将轴和膜片从臂组件上卸下,以便拆卸。
Show/hide table图 14 g00595744 - 将下部的黄铜接头 (25) 卸下。
- 翻转壳体。
Show/hide table
图 15 g00595746 - 将上部的黄铜接头 (26) 卸下。
- 卸下垫圈 (27)。
Show/hide table
图 16 g00595747 Show/hide table图 17 g00595748 - 卸下垫圈 (28) 和膜片组件 (29)。
注: 标记外壳以便正确安装。
- 轻敲外壳上部 (30),卸下膜片组件 (31)。
- 卸下喷嘴 (32)。
Show/hide table
图 18 g00595749 (33) 阀。 (34) 膜片。 (35) O 形密封圈。 (36) 垫圈。 (37) 适配器。 - 拆解小型膜片组件 (31)。
Show/hide table
图 19 g00595751 - 卸下大尺寸 T 形管 (38)。
- 如有必要,从 T 形管上卸下阀柱塞组件 (39)。
Show/hide table
图 20 g00595752 - 卸下开口销 (40),以便能够将轴组件 (41) 推入阀中。 应将轴组件推远,以便接触臂组件。
Show/hide table
图 21 g00595754 - 卸下两个固定夹 (43) 和销 (42),以便从调节器壳体卸下臂 (44) 和轴 (41)。
Show/hide table
图 22 g00595755 (40) 销。 (41) 轴组件。 (42) 销。 (43) 固定夹。 (44) 臂。 (45) 密封件。 (46) 螺母。 (47) 盖。 - 拆解气压调节器的盖。
Show/hide table
图 23 g00595757 (40) 销。 (48) 轴。 (49) 阀室盖。 (50) 衬套。 (51) 护圈。 (52) 螺钉。 - 拆解阀柱塞组件。
Show/hide table
图 24 g00595758 Show/hide table图 25 g00595759 - 从盖 (23) 上卸下轴组件 (53)。
- 从盖 (23) 上卸下导向装置 (54)。
- 卸下垫圈 (55)。
- 卸下膜片 (56)。
Show/hide table
图 26 g00595761 (23) 盖。 (54) 导向装置。 (55) 垫圈。 (56) 膜片。 (57) 接头。 (58) 护圈。 (59) 轴。 - 拆解大型膜片组件。
Show/hide table
图 1 | g00592537 |
Caterpillar Information System:
SR4B Generators Generator - Align
G3612 and G3616 Engines Gas Pressure Regulator - Install
G3612 and G3616 Engines Gas Pressure Regulator - Remove
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 4 Spare Output Voltage Below Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 3 Spare Output Voltage Above Normal - Test
G3612 and G3616 Engines Crankshaft - Install
3126B Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
C9 On-Highway Engines General Information
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Remove
G3612 and G3616 Engines Gas Pressure Regulator - Assemble
3054 and 3056 Industrial and Generator Set Engines Engine Storage
3512B Marine Auxiliary Engine Analog Sensor Supply
3512B Marine Auxiliary Engine CAT Data Link
3512B Marine Auxiliary Engine Digital Sensor Supply
3512B Marine Auxiliary Engine Electrical Power Supply
C-15, C-16 and C-18 Truck Engines Engine Oil Pressure Sensor - Remove and Install
3114, 3116 and 3126 Engines Excessive Blue Smoke
G3612 and G3616 Engines Actuator (Hydrax) - Remove
G3612 and G3616 Engines Actuator (Hydrax) - Install
G3612 and G3616 Engines Actuator (Hydrax) - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 443 FMI 12 Crank Termination Relay Failed - Test