Engine Oil Pump - Disassemble
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 7S-7786     | 拉拔器腿     | 2     |
5F-7345 | 螺钉     | 1     |
开始:
- 拆下发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 将两条螺栓、机油吸油管 (2) 和密封垫从机油泵上拆下。 将一条螺栓和出口弯头 (1) 从机油泵上拆下。
Show/hide table
图 1 | g00614664 |
- 将螺栓 (3) 、垫圈 (4) 和惰轮 (5) 从机油泵上拆下。
Show/hide table
图 2 | g00614677 |
- 利用工具 (A) 和适当的压具将轴承从惰轮 (5) 上拆下。
Show/hide table
图 3 | g00614683 |
- 将轴 (6) 从机油泵壳体组件 (7) 上拆下。
- 利用工具 (B) 拆下驱动齿轮 (8) 。
- 拆下螺栓 (10) 。 将机油泵壳 (9) 从机油泵壳体组件 (7) 上分离。
Show/hide table
图 4 | g00614689 |
- 将轴组件 (11) 和 (12) 从机油泵壳 (9) 上拆下。
Show/hide table
图 5 | g00614694 |
Show/hide table
注意 |
---|
从泵壳上拆下驱动轴之前,确保驱动轴上没有毛刺。 如果驱动轴上有毛刺,很可能会划伤泵壳内孔。 |
- 将以下各项从机油泵壳体组件 (7) 上拆下:螺栓和垫圈, 弹簧 (14) 和 机油卸压柱塞 (13) 。
Show/hide table
图 6 | g00614696 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 331 FMI 2 Switch (Engine Control) Incorrect Signal - Test
SR4B Generators Rotor - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
G3612 and G3616 Engines Crankshaft - Remove
SR4B Generators Bearing - Remove and Install
G3612 and G3616 Engines Crankshaft Main Bearings - Install
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove
G3304 and G3306 Engines Cylinder Head
SR4B Generators Coupling - Remove
C9 On-Highway Engines General Information
3126B Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
G3612 and G3616 Engines Crankshaft - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 3 Spare Output Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 4 Spare Output Voltage Below Normal - Test
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Assemble
G3612 and G3616 Engines Gas Pressure Regulator - Remove
G3612 and G3616 Engines Gas Pressure Regulator - Install
SR4B Generators Generator - Align
G3612 and G3616 Engines Gas Pressure Regulator - Disassemble
G3612 and G3616 Engines Gas Pressure Regulator - Assemble
3054 and 3056 Industrial and Generator Set Engines Engine Storage