General Information
C9 发动机为直列六缸布置。 发动机的点火顺序为 "1-5-3-6-2-4"。 发动机按照由发动机飞轮端观看的逆时针方向旋转。 发动机采用一个涡轮增压器。 发动机的缸径为 112 mm (4.41 英寸),冲程为 149 mm (5.87 英寸)。 排量为 8.8 L (537 cu in)。
C9 发动机利用液压电子式单体喷油器 (HEUI) 进行喷油操作。HEUI系统所使用的一套油泵管路系统除去了许多机械零部件。 HEUI 可以提高正时和空燃比的控制。 正时提前是通过单体喷油器正时的精确控制来完成的。 发动机转速是由调整喷油持续时间来控制的。 有一个特殊的脉冲轮向发动机控制模块 (ECM) 提供信息,以便检测气缸位置和发动机转速。
发动机内置有诊断系统,以便确保所有部件工作正常。 如果一个系统部件出现故障,则可以通过仪表板上的检查发动机指示灯提醒驾驶员这个状况。 卡特彼勒电子技师 (ET) 可用于读取数字代码,指示出有问题的零部件或状况。 此外,巡航控制开关也可用于在检查发动机指示灯上闪烁代码。 间歇性故障会记录和储存在存储器内。
起动发动机
发动机 ECM 将自动提供起动发动机所需的正确燃油量。 盘车起动发动机时不要踩下油门。 如果发动机二十秒内没有起动,则应松开起动开关。 再次使用起动马达之前让起动马达先冷却两分钟。
Show/hide table
注意 |
---|
选装的自动乙醚喷射系统是唯一推荐使用的起动液系统。 乙醚过量使用会造成活塞和活塞环损坏。 只能在冷天起动时使用辅助起动液(乙醚)。 |
寒冷天气起动
寒冷天气发动机的起动和运转性能取决于燃油类型、机油粘度和其它选装的起动辅助装置。 请参阅操作和保养手册, "寒冷天气操作"部分(操作一节),了解更多资料。
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 331 FMI 2 Switch (Engine Control) Incorrect Signal - Test
SR4B Generators Rotor - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
G3612 and G3616 Engines Crankshaft - Remove
SR4B Generators Bearing - Remove and Install
G3612 and G3616 Engines Crankshaft Main Bearings - Install
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
G3612 and G3616 Engines Crankshaft - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 3 Spare Output Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 4 Spare Output Voltage Below Normal - Test
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Assemble
G3612 and G3616 Engines Gas Pressure Regulator - Remove
G3612 and G3616 Engines Gas Pressure Regulator - Install
SR4B Generators Generator - Align
G3612 and G3616 Engines Gas Pressure Regulator - Disassemble
G3612 and G3616 Engines Gas Pressure Regulator - Assemble
3054 and 3056 Industrial and Generator Set Engines Engine Storage
3512B Marine Auxiliary Engine Analog Sensor Supply