Gas Pressure Regulator - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 组装大型膜片组件。
Show/hide table
图 2 g00595758 Show/hide table图 3 g00595759 - 安装膜片 (56)。
- 安装垫圈 (55)。
- 将导向装置 (54) 安装在盖 ( 23) 上。
- 将轴组件 (53) 安装至盖 ( 23) 内。
Show/hide table
图 4 g00595757 (40) 销。 (48) 轴。 ( 49) 阀室盖。 (50) 衬套。 ( 51) 护圈。 (52) 螺钉。 - 组装阀柱塞组件。
Show/hide table
图 5 g00595755 (40) 销。 (41) 轴组件。 ( 42) 销。 (43) 固定夹。 ( 44) 臂。 (45) 密封件。 ( 46) 螺母。 (47) 盖。 - 组装气压调节器的盖。
Show/hide table
图 6 g00595754 - 将臂 (44) 和轴 ( 41) 定位在调节器壳体内。 安装两个新的固定夹 ( 43) 和销 (42)。
Show/hide table
图 7 g00595752 - 将开口销 (40) 安装在轴组件 ( 41) 内。
Show/hide table
图 8 g00595751 - 如果卸下阀柱塞组件,则将阀柱塞组件 ( 39) 安装在 T 形管内。
- 安装大尺寸 T 形管 ( 38)。
Show/hide table
图 9 g00595749 (33) 阀。 (34) 膜片。 ( 35) O 形密封圈。 (36) 垫圈。 ( 37) 适配器。 Show/hide table图 10 g00595747 - 组装小型膜片组件 ( 31)。
Show/hide table
图 11 g00595748 - 卸下喷嘴 (32)。
- 将外壳上部 (30) 安装在膜片组件 ( 31) 内。
- 安装垫圈 (28) 和膜片组件 ( 29)。 确保将膜片安置在恰当位置。
Show/hide table
图 12 g00595746 - 安装垫圈 (27)。
- 安装上部黄铜接头 ( 26)。
- 翻转壳体。
Show/hide table
图 13 g00595744 - 安装下部黄铜接头 ( 25)。
Show/hide table
图 14 g00595743 - 将盖 (23)、轴和膜片作为整体进行安装。
Show/hide table
图 15 g00595605 - 将十二个螺栓 (24) 安装在壳体 ( 23) 内。
注: 小心地将弹簧安装至壳体内。 弹簧受压。
Show/hide table图 16 g00595603 - 安装护圈 (21) 和弹簧 ( 22)。
注: 确保将螺纹护圈拧至恰当位置。
Show/hide table图 17 g00595600 - 请检查垫片是否损坏。 如有必要,更换垫片。 安装壳体 (19) 和垫片。
- 安装四个螺栓 (20)。
- 翻转气压调节器。
Show/hide table
图 18 g00595596 - 安装接头 (18)。
Show/hide table
图 19 g00595593 - 安装垫圈 (16) 和弹簧 ( 17)。
Show/hide table
图 20 g00595590 - 安装壳体 (14)。
- 安装八个螺栓 (15)。
Show/hide table
图 21 g00595587 (7) 阀体。 (9) 螺钉。 ( 10) 垫圈。 (11) 滤芯。 ( 12) 垫圈。 (13) 盖。 Show/hide table图 22 g00595584 - 组装滤芯组件 (8)。
- 将阀体 (7) 安装至滤芯组件 ( 8) 内。
Show/hide table
图 23 g00595582 - 安装阀 (6)。
Show/hide table
图 24 g00595580 - 安装管组件 (4)。
- 安装管组件 (5)。
Show/hide table
图 25 g00595577 - 拧紧调整螺钉。
注: 确保调整螺钉回到原始位置。
- 拧紧防松螺母 (2)。
Show/hide table
图 1 | g00595761 |
(23) 盖。 (54) 导向装置。 ( 55) 垫圈。 (56) 膜片。 ( 57) 接头。 (58) 护圈。 ( 59) 轴。 |
Show/hide table
图 26 | g00592537 |
结束:
- 安装气压调节器 ( 1)。
Caterpillar Information System:
G3612 and G3616 Engines Gas Pressure Regulator - Disassemble
SR4B Generators Generator - Align
G3612 and G3616 Engines Gas Pressure Regulator - Install
G3612 and G3616 Engines Gas Pressure Regulator - Remove
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 4 Spare Output Voltage Below Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 334 FMI 3 Spare Output Voltage Above Normal - Test
G3612 and G3616 Engines Crankshaft - Install
3126B Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
C9 On-Highway Engines General Information
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3054 and 3056 Industrial and Generator Set Engines Engine Storage
3512B Marine Auxiliary Engine Analog Sensor Supply
3512B Marine Auxiliary Engine CAT Data Link
3512B Marine Auxiliary Engine Digital Sensor Supply
3512B Marine Auxiliary Engine Electrical Power Supply
C-15, C-16 and C-18 Truck Engines Engine Oil Pressure Sensor - Remove and Install
3114, 3116 and 3126 Engines Excessive Blue Smoke
G3612 and G3616 Engines Actuator (Hydrax) - Remove
G3612 and G3616 Engines Actuator (Hydrax) - Install
G3612 and G3616 Engines Actuator (Hydrax) - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 443 FMI 12 Crank Termination Relay Failed - Test
G3612 and G3616 Engines Actuator (Hydrax) - Assemble