Boom - Stub Boom
Show/hide table
Illustration 1 | g03398743 |
Show/hide table
Specification for 123-8931 Stub Boom     | |||
Item     | Qty     | Part     | Specification Description     |
All bores must be free of paint. Coat all bores for pins with the lubricant including fore boom, the upper frame, and the cylinder pin bores.     | |||
1     | 2     | 258-8502 Bushing     | Bore of the bushing before assembly is 70.27 ± 0.04 mm (2.767 ± 0.002 inch).     |
Installation depth is 7.0 ± 0.5 mm (0.28 ± 0.02 inch). |
|||
2     | 2     | 128-7656 Bushing     | Bore of the bushing before assembly is 70.23 ± 0.02 mm (2.765 ± 0.001 inch).     |
Installation depth is 7.5 mm (0.30 inch). |
|||
3     | 6     | 8T-4956 Bolt     | Torque to 120 ± 20 N·m (89 ± 15 lb ft).     |
4     | 1     | 093-0118 Shim     | As required, use the shim with the thickness of 2.0 mm (0.08 inch) to adjust lateral clearance to a total maximum of 1.6 mm (0.06 inch) and a total minimum of 0.5 mm (0.02 inch) for each boom cylinder eye.     |
5     | 1     | 093-0086 Shim     | As required, use the shim with the thickness of 1.0 mm (0.04 inch) to adjust lateral clearance to a total maximum of 1.6 mm (0.06 inch) and a total minimum of 0.5 mm (0.02 inch) for each boom cylinder eye.     |
6     | 1     | 120-8520 Pin As     | Diameter is 69.850 ± 0.025 mm (2.7500 ± 0.0010 inch).     |
7     | 1     | 8T-4780 Bolt     | Torque to 570 ± 80 N·m (420 ± 59 lb ft).     |
8     | 1     | 093-0118 Shim     | As required, use the following shim with the thickness of 2.0 mm (0.08 inch) to adjust lateral clearance to maximum of 1.0 mm (0.04 inch).     |
9     | 4     | 093-1434 Lip Type Seal     | Before assembly, lightly lubricate the sealing lip with the 5P-0960 Grease Cartridge .     |
10     | As required, use the following shims to adjust lateral clearance to maximum of 1.0 mm (0.04 inch):     |
||
1 | 093-0086 Shim     | Thickness is 1.0 mm (0.04 inch).     |
|
1 | 7Y-2496 Shim     | Thickness is 1.6 mm (0.06 inch).     |
|
11     | 1     | 173-1342 Pin     | Diameter is 69.950 ± 0.025 mm (2.7539 ± 0.0010 inch).     |
12     | 1     | 133-2424 Shim     | As required, use the following shim with the thickness of 0.5 mm (0.02 inch) to adjust lateral clearance to maximum of 1.0 mm (0.04 inch).     |
Caterpillar Information System:
315B L Excavator Cooling System Level - Check
315B and 315B L Excavator Hydraulic System Relief Valve (One Way Flow Line) - Test and Adjust
315B L Excavator Cooling System Hoses - Inspect
311B and 312B Excavators Hydraulic System Pressure Specifications - 311B
315B L Excavator Cooling System Coolant Extender (ELC) - Add
315B L Excavator Cooling System Coolant Additive (DEAC) - Add
315B L Excavator Fuel System Secondary Filter - Replace
315B L Excavator Fuel System Priming Pump Strainer - Clean
312B Excavator Attachments General Information
315B L Excavator Fuel System Priming Pump - Operate
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Fire Extinguisher Location
315B L Excavator Engine Oil and Filter - Change
315B L Excavator Storage Box
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Accumulator - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Alternator and Regulator
312B Excavator Attachments Lowering Control Valve (Boom) - Test
M312 Excavator Machine System Boom - Fore Boom
311B and 312B Excavators Hydraulic System Pressure Specifications - 312B and 312B L
312B Excavator Attachments Two-Way Hydraulic Flow Operation
311B and 312B Excavators Hydraulic System Relief Valve (Pilot) - Test and Adjust
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Fuel System Water Separator - Drain
M312 Excavator Machine System Lines (Hammer) - Boom (One Piece)
311B and 312B Excavators Hydraulic System Relief Valve (Main) - Test and Adjust
5130 Excavator Hydraulic System Pump Drive