Turbocharger - Remove
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
 | |
| Illustration 1 | g01029881 |
- Remove tube assemblies (2) and (3) from the turbocharger. Check the condition of the O-ring seals on tube assemblies (2) and (3). Use new parts for replacement if the O-ring seals are worn or damaged.
- Use a suitable lifting device. The turbocharger weighs approximately 34 kg ( 75 lb).
- Remove bolts (4).
Show/hide table
 | |
| Illustration 2 | g01029884 |
- Remove turbocharger (1) .
Caterpillar Information System:
3500B Engines Engine Oil Pan
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0336 - FMI 02 Incorrect ECS Switch inputs
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0289 - FMI 13 Unfiltered Fuel Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0289 - FMI 03 Unfiltered Fuel Pressure open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 04 Left Turbo Inlet Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 03 Left Turbo Inlet Pressure open/short to +batt
3612 and 3616 Engines Engine Support
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0275 - FMI 13 Right Turbo Inlet Pressure calibration required
3612 and 3616 Engines Engine Support
Electronic Modular Control Panel II (EMCP II) For MUI Engines Diagnostic Codes
3612 and 3616 Engines Flywheel
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0275 - FMI 04 Right Turbo Inlet Pressure short to ground
3406E and 3456 Generator Set Engines Turbocharger - Install
3176C and 3196 Engines for Caterpillar Built Machines Connecting Rod Bearings - Inspect
Electronic Modular Control Panel II (EMCP II) For MUI Engines Relay (Overvoltage)
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Piston and Rings
3176C and 3196 Engines for Caterpillar Built Machines Main Bearings - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Block - Inspect
3126B Marine Engine Turbocharger
3126B Marine Engine Aftercooler
3176C and 3196 Engines for Caterpillar Built Machines Cylinder Liner Projection - Inspect
3500B Engines and 3500 Engines with EUI Option Air Shutoff System
Accessing Flash Software for Machines{7610, 7620} Accessing Flash Software for Machines{7610, 7620}
Electronic Modular Control Panel II (EMCP II) For MUI Engines Relay (Overcurrent)