The Cab Door Interior Handle May Become Loose On Certain Excavators
Usage:
EXCAVATORS322B L (1YS),
325B L (2JR),
330B L (6DR),
345 (2NW),
345B L (4SS, 9GS),
350 (2ZL),
350 L (3ML) 375 (8WJ),
375 L (1JM),
5080 (8SL) EXCAVATORS
325B L (2JR),
330B L (6DR),
345 (2NW),
345B L (4SS, 9GS),
350 (2ZL),
350 L (3ML) 375 (8WJ),
375 L (1JM),
5080 (8SL) EXCAVATORS
Problem:
There have been reports that the cab door interior handle has vibrated loose on certain Excavators. If the handle vibrates loose, it can separate from the mounting pin.
Solution:
Apply 9S-3263 Compound to the external and internal threads of the 6C-8993 Pin. Assemble the pin to the pivot in the door handle assembly. Apply 169-5464 Primer to the internal threads of the 156-5081 Handle. Hand tighten the handle to the pin.
Typical interior cab door handle assembly.
Illustration 1.
COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar Information System:
Auxiliary Hydraulic Control Pedal Does Not Operate Correctly Auxiliary Hydraulic Control Pedal Does Not Operate Correctly
Rubbing And Wear Of Alternator Breaker Wires Rubbing And Wear Of Alternator Breaker Wires
Hydraulic Horsepower Testing Hydraulic Horsepower Testing
Service Support Literature Identified For Certain Track-Type Excavators Service Support Literature Identified For Certain Track-Type Excavators
Switch Contacts Become Tarnished Switch Contacts Become Tarnished
Engine Fueling Overheating Engine Fueling Overheating
Lower Windshield Glass For Cab Is Identified Incorrectly Lower Windshield Glass For Cab Is Identified Incorrectly
Increased Case Drain Pressure May Cause Swing Motor Failure (Reoccurence) Increased Case Drain Pressure May Cause Swing Motor Failure (Reoccurence)
Valve Spring Failures On 3100 Engines Produced By Shin Caterpillar Mitsubishi (SCM) At Sagami Valve Spring Failures On 3100 Engines Produced By Shin Caterpillar Mitsubishi (SCM) At Sagami
Swing Drive Seals May Be Installed Incorrectly On Certain Large Mining Excavators Swing Drive Seals May Be Installed Incorrectly On Certain Large Mining Excavators
Efficiency Check For The Travel Make-Up Flow During Travel Operation Efficiency Check For The Travel Make-Up Flow During Travel Operation
Turbocharger Drain Tube Gasket May Leak Turbocharger Drain Tube Gasket May Leak
VIMS-PC Version 2.4 Will Not Open After Installation Of Electronic Technician Version 3.0 VIMS-PC Version 2.4 Will Not Open After Installation Of Electronic Technician Version 3.0
Changing The Pattern Of The Joystick Controls Changing The Pattern Of The Joystick Controls
Wiper Motor Identification Is Explained For Certain Excavators Wiper Motor Identification Is Explained For Certain Excavators
Replacing The Damper Assembly On The Engine Crankshaft Replacing The Damper Assembly On The Engine Crankshaft
Engine Oil Coolers May Leak At The Sealing Surface Between The Oil Cooler And The Engine Block Engine Oil Coolers May Leak At The Sealing Surface Between The Oil Cooler And The Engine Block
Monitor Panel Display Remains In The Self-Test Mode Monitor Panel Display Remains In The Self-Test Mode
XT6 Hose on 375 Excavators Replaces the XT5 Hose To Increase Reliability And Durability XT6 Hose on 375 Excavators Replaces the XT5 Hose To Increase Reliability And Durability
151-6617 Bracket For The Air Conditioner Refrigerant Compressor May Break 151-6617 Bracket For The Air Conditioner Refrigerant Compressor May Break
Operation Of 119-1733 And 134-1346 12-Volt Converters Operation Of 119-1733 And 134-1346 12-Volt Converters
Lubrication Of The Bearing In The Fan Belt Tension Pulley On Certain Excavators Lubrication Of The Bearing In The Fan Belt Tension Pulley On Certain Excavators
Lower Windshield Latches May Be Assembled With An Incorrect Spacer On Certain Excavators Lower Windshield Latches May Be Assembled With An Incorrect Spacer On Certain Excavators
Restriction Port Indicator May Not Function Restriction Port Indicator May Not Function