Temperature Contactor
Show/hide table
图 1 | g00541118 |
Show/hide table
温度接触器 (1)     | ||
接触器     | 工作温度 (2)     | 工作温度 (3)     |
4P-6032     | 66 ± 2 °C (151 ± 4 °F)     |
58 ± 2 °C (136 ± 4 °F)     |
4P-6036     | 104 ± 2 °C (219 ± 4 °F)     |
98 ± 2 °C (208 ± 4 °F)     |
120-1214     | 106 ± 2 °C (223 ± 4 °F)     |
100 ± 2 °C (212 ± 4 °F)     |
120-1218     | 100 ± 2 °C (212 ± 4 °F)     |
94 ± 2 °C (201 ± 4 °F)     |
Show/hide table
( 1 ) | 上述温度接触器有 8 个仪表毛细管。 |
( 2 ) | 温度升高时,接触器在上述范围内工作。 |
( 3 ) | 温度降低时,接触器在上述范围内工作。 |
Show/hide table
温度接触器 (1)     | ||
接触器     | 工作温度 (2)     | 工作温度 (3)     |
7C-3888     | 66 ± 2 °C (151 ± 4 °F)     |
58 ± 2 °C (136 ± 4 °F)     |
7C-4926     | 95 ± 2 °C (203 ± 4 °F)     |
90° ± 2°C (194 ± 4 °F)     |
7C-4927     | 130 ± 3 °C (266 ± 5 °F)     |
120 ± 3 °C (248 ± 5 °F)     |
120-1207     | 106 ± 2 °C (223 ± 4 °F)     |
100 ± 2 °C (212 ± 4 °F)     |
120-1210     | 100 ± 2 °C (212 ± 4 °F)     |
94 ± 2 °C (201 ± 4 °F)     |
Show/hide table
( 1 ) | 上述温度接触有 3 个仪表毛细管。 |
( 2 ) | 温度升高时,接触器在上述范围内工作。 |
( 3 ) | 温度降低时,接触器在上述范围内工作。 |
Caterpillar Information System:
G3500B Engines Ignition System Spark Plugs - Inspect/Replace - Spark Plugs that have Precombustion Chambers
G3500B Engines Fuel System Fuel Filter Differential Pressure - Check
The Installation And The Alignment Of The Two-Bearing Locomotive Generators{4471} The Installation And The Alignment Of The Two-Bearing Locomotive Generators{4471}
3116 Truck Engine Engine Oil Level - Check
3116 Truck Engine Engine Crankcase Breather - Clean
3408E and 3412E Engines for Caterpillar Built Machines Electric Starting System - Test
G3606 and G3608 Engines Water Lines - Remove and Install
3054 Truck Engine Reference Material
G3500 Engines Flywheel Housing - Remove
G3606 and G3608 Engines Water Temperature Regulator and Housing - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Jacket Water Heater
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Travel Motor - Test
G3606 and G3608 Engines Crankcase Pressure Sensor - Remove and Install
3116 Truck Engine Engine Oil and Filter - Change
G3606 and G3608 Engines Fuel Shutoff Solenoid - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Relief Valve (Travel Motor) - Test and Adjust
G3500 Engines Overhaul (In-Frame)
Electronic Modular Control Panel II+ (EMCP II+) Parallel Setpoint Viewing OP2-3
G3500 Engines Flywheel Housing - Install
G3500B Engines Overhaul (Major)
G3500B Engines Overhaul (Top End)
3116 Truck Engine Fuel Injection Timing - Check
G3606 and G3608 Engines Air Silencer - Remove and Install
3116 Truck Engine Fuel Inlet Screen - Clean/Inspect/Replace