PRODUCT SUPPORT PROGRAM FOR REPLACING THE VP30 FUEL PUMP ON CERTAIN 315C TRACKED EXCAVATORS
Usage:
SEBE9387-01
November 6, 2005
(Revised December 2005)
U-352
D-277
O-291
Show/hide table
| before
or after failure |
PRODUCT SUPPORT PROGRAM FOR REPLACING THE VP30 FUEL PUMP ON CERTAIN 315C TRACKED EXCAVATORS |
|
| 1251 1290 |
PS41887
|
|
NOTE: The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
NOTE: This Revised Service Letter replaces the November 6, 2005 Service Letter. Changes have been made to the Action Required Section.
TERMINATION DATE
November 30, 2006PROBLEM
There have been failures of the DMV10 Timing Solenoid within the fuel injection pump (234-3454 FIP As.) at early hours on 315C Excavators, causing poor performance, de-rate and failure to start. Symptoms of failed Timing Solenoids include the following- 1684-11 Fuel Pump Fault Code present by itself (no other fault codes should be present)
- Engine will also have heavy knocking noise and sound advanced
AFFECTED PRODUCT
Show/hide table
| Model | Identification Number |
| 315C |
|
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
| 1 | 1458327 | SEAL-O-RING |
| 1 | 2343454 | PUMP GP-F IN |
ACTION REQUIRED
- Remove counterweight to facilitate fuel pump inspection
- Confirm Fuel pump is in affected population by reviewing pump date code (see Illustration 1) carry out repair as per RENR2411.
Show/hide table
| FIP | Date Code of Affected Range |
| 234-3454 | 383 TO 484 |
Illustration 1
SERVICE CLAIM ALLOWANCES
Show/hide table
Product smu/age whichever comes first |
|
|
|
|||
Parts |
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
| NOTE: *The
2.0 hour of labor is for removal of counterweight and fuel pump date code
inspection
NOTE: **The 5.0 hours is for the fuel pump replacement only |
||||||
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.Caterpillar Information System:
PRODUCT SUPPORT PROGRAM FOR INSPECTING AND TIGHTENING THE LOCK NUTS FOR THE BUCKET AND STICK CYLINDERS ON CERTAIN 312C, 312C L, 315C, AND 315C L HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSPECTING AND TIGHTENING THE LOCK NUTS FOR THE BUCKET AND STICK CYLINDERS ON CERTAIN 312C, 312C L, 315C, AND 315C L HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE ULTRA HIGH DEMOLITION FORE BOOM ON CERTAIN 330C EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE ULTRA HIGH DEMOLITION FORE BOOM ON CERTAIN 330C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPAIRING THE STICK ON CERTAIN 304 CR AND 305 CR MINI HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPAIRING THE STICK ON CERTAIN 304 CR AND 305 CR MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING AN O-RING ONTO THE FUEL PRESSURE REGULATOR VALVE ON CERTAIN 345C, 365C, AND 385C EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSTALLING AN O-RING ONTO THE FUEL PRESSURE REGULATOR VALVE ON CERTAIN 345C, 365C, AND 385C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPOSITIONING THE HIGH PRESSURE WATER PUMP ON CERTAIN SF-200R AND SF-200RS COLD PLANERS PRODUCT IMPROVEMENT PROGRAM FOR REPOSITIONING THE HIGH PRESSURE WATER PUMP ON CERTAIN SF-200R AND SF-200RS COLD PLANERS
PRODUCT SUPPORT PROGRAM FOR INSTALLING A NEW 250-5252 HANDRAIL ON CERTAIN 365B L, 365B L SERIES II EXCAVATORS AND 365B L SERIES II MATERIAL HANDLERS PRODUCT SUPPORT PROGRAM FOR INSTALLING A NEW 250-5252 HANDRAIL ON CERTAIN 365B L, 365B L SERIES II EXCAVATORS AND 365B L SERIES II MATERIAL HANDLERS
PRODUCT SUPPORT PROGRAM FOR REPLACING VARIOUS HYDRAULIC HOSES ON CERTAIN 312C, 315C, 318C, 319C, 320C, 322C, 325C, 325C L, 330C, AND 330C L EXCAVATORS AND M325C MATERIAL HANDLERS PRODUCT SUPPORT PROGRAM FOR REPLACING VARIOUS HYDRAULIC HOSES ON CERTAIN 312C, 315C, 318C, 319C, 320C, 322C, 325C, 325C L, 330C, AND 330C L EXCAVATORS AND M325C MATERIAL HANDLERS
PRODUCT SUPPORT PROGRAM FOR IMPROVING THE QUICK COUPLER OPERATION ON CERTAIN 304, 304.5, AND 305 MINI HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR IMPROVING THE QUICK COUPLER OPERATION ON CERTAIN 304, 304.5, AND 305 MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM REPAIRING THE WELD ON THE BUCKET HINGE PLATE PIN BOSS ON CERTAIN 320C, 325C, AND 330C EXCAVATORS PRODUCT IMPROVEMENT PROGRAM REPAIRING THE WELD ON THE BUCKET HINGE PLATE PIN BOSS ON CERTAIN 320C, 325C, AND 330C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 194-8321 ROD ASSEMBLY FOR THE STICK CYLINDER ON CERTAIN 325C AND 325C L EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE 194-8321 ROD ASSEMBLY FOR THE STICK CYLINDER ON CERTAIN 325C AND 325C L EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR IMPROVING THE LEVELING CAPABILITY ON CERTAIN 320C EXCAVATORS THAT ARE EQUIPPED WITH HEAVY FRONT END COMPONENTS PRODUCT SUPPORT PROGRAM FOR IMPROVING THE LEVELING CAPABILITY ON CERTAIN 320C EXCAVATORS THAT ARE EQUIPPED WITH HEAVY FRONT END COMPONENTS
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING THE SAFETY ALARM ON CERTAIN 325C L AND 330C L EXCAVATORS THAT ARE EQUIPPED WITH A PIN GRABBER PLUS QUICK COUPLER PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING THE SAFETY ALARM ON CERTAIN 325C L AND 330C L EXCAVATORS THAT ARE EQUIPPED WITH A PIN GRABBER PLUS QUICK COUPLER
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE MAIN PUMP COUPLING ON CERTAIN M313C, M315C, M316C, M318C, AND M322C WHEELED HYDRAULIC EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE MAIN PUMP COUPLING ON CERTAIN M313C, M315C, M316C, M318C, AND M322C WHEELED HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REFLASHING SOFTWARE ON THE PRODUCT LINK 300 MODULE FOR CERTAIN CATERPILLAR PRODUCTS PRODUCT IMPROVEMENT PROGRAM FOR REFLASHING SOFTWARE ON THE PRODUCT LINK 300 MODULE FOR CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 204-0890 COOLER ASSEMBLY ON CERTAIN 325C AND 325C L EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE 204-0890 COOLER ASSEMBLY ON CERTAIN 325C AND 325C L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR TORQUING THE SWING BEARING MOUNTING BOLTS ON CERTAIN 321C LCR EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR TORQUING THE SWING BEARING MOUNTING BOLTS ON CERTAIN 321C LCR EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM REPLACING THE ROTATOR GROUP ON CERTAIN G320B AND VRG-30/2 GRAPPLES PRODUCT IMPROVEMENT PROGRAM REPLACING THE ROTATOR GROUP ON CERTAIN G320B AND VRG-30/2 GRAPPLES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE MOUNTING BOLTS FOR THE COUNTERWEIGHT ON CERTAIN 345C EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE MOUNTING BOLTS FOR THE COUNTERWEIGHT ON CERTAIN 345C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN FUEL INJECTORS FROM DEALERS PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN FUEL INJECTORS FROM DEALERS PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW HANDRAILS ON CERTAIN 345B SERIES II EXCAVATORS THAT ARE EQUIPPED WITH A WIDE HEAVY DUTY UNDERCARRIAGE IN ORDER TO IMPROVE ACCESS TO THE CAB AND ACCESS PLATFORM PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW HANDRAILS ON CERTAIN 345B SERIES II EXCAVATORS THAT ARE EQUIPPED WITH A WIDE HEAVY DUTY UNDERCARRIAGE IN ORDER TO IMPROVE ACCESS TO THE CAB AND ACCESS PLATFORM
PRODUCT SUPPORT PROGRAM FOR INSPECTION AND REPAIR OF CERTAIN 301.6C, 301.8C AND 302.5C MINI HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSPECTION AND REPAIR OF CERTAIN 301.6C, 301.8C AND 302.5C MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE CAM PLATE FOR THE TRAVEL MOTOR ON CERTAIN 325C AND 330C EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE CAM PLATE FOR THE TRAVEL MOTOR ON CERTAIN 325C AND 330C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REWORKING THE THREAD DEPTH OF THE M16 MOUNTING HOLES IN THE MAIN CONTROL VALVE ON CERTAIN 320C, 320C L, 320C LU, AND 330C L HYDRAULIC EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REWORKING THE THREAD DEPTH OF THE M16 MOUNTING HOLES IN THE MAIN CONTROL VALVE ON CERTAIN 320C, 320C L, 320C LU, AND 330C L HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM TO INSTALL DECALS AND A NEW OPERATION AND MAINTENANCE MANUAL FOR CERTAIN CATERPILLAR PIN GRABBER COUPLERS PRODUCT IMPROVEMENT PROGRAM TO INSTALL DECALS AND A NEW OPERATION AND MAINTENANCE MANUAL FOR CERTAIN CATERPILLAR PIN GRABBER COUPLERS