Walk-Around Inspection
Show/hide table
Personal injury or death can result from improperly checking for a leak. Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury. |
Show/hide table
NOTICE |
---|
Accumulated grease and oil on a machine is a fire hazard. Remove this debris with steam cleaning or high pressure water, at least every 1000 hours or each time any significant quantity of oil is spilled on a machine. |
Note: If major repairs to the demolition tool are required, consult your Caterpillar dealer.
- For the maximum service life of the work tool, make a thorough walk-around inspection before mounting the machine and starting the engine.
- Inspect the work tool for the following conditions: loose bolts, worn cutter, worn teeth and oil leaksbroken parts and worn parts. Inspect the work tool for missing parts. Check the overall condition of the work tool. Check the overall condition of the hydraulic system.
- Inspect the condition of the hydraulic lines and the hydraulic fittings.
- Inspect the cutting jaw. Remove scrap from the jaw.
- Inspect the welds, the pins, and the bores for damage. If the components are damaged, consult your Caterpillar dealer.
- Perform all repairs before putting the work tool into service.
- Check the hydraulic oil. Maintain the oil to the proper level. Refer to the Operation and Maintenance Manual for your machine.
Show/hide table
Illustration 1 | g00475781 |
Caterpillar Information System:
P16, P20, P25, P28, P40 and P60 Pulverizer Principles of Breaking
3126E and 3126B Commercial and Truck Engines General Hazard Information
3208 Marine Engine Fuel System - Prime
3406E, C-10, C-12, C-15, C-16 Truck Engines Starting the Engine
P16, P20, P25, P28, P40 and P60 Pulverizer Operating Technique Information
Installation Of The Hydraulic Actuator System (Hydrax System) on G3606 and G3608 Engines {1050, 1250, 1908, 1915} Installation Of The Hydraulic Actuator System (Hydrax System) on G3606 and G3608 Engines {1050, 1250, 1908, 1915}
3208 Marine Engine Fuel System Water Separator - Drain
3208 Marine Engine Fuel Ratio Control - Inspect/Adjust
P16, P20, P25, P28, P40 and P60 Pulverizer Ring Gear - Lubricate
3208 Marine Engine Engine Oil Level - Check
3208 Marine Engine Fuel System Secondary Filter - Replace
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Description
3126E and 3126B Commercial and Truck Engines Mounting and Dismounting
3126E and 3126B Commercial and Truck Engines Engine Starting
Installation Of The 129-6628 Speed/Timing Sensor On 3406E Engines{1907} Installation Of The 129-6628 Speed/Timing Sensor On 3406E Engines{1907}
P16, P20, P25, P28, P40 and P60 Pulverizer Specifications
Instructions for the Service Replacement of the Turbochargers{1052} Instructions for the Service Replacement of the Turbochargers{1052}
3126E and 3126B Commercial and Truck Engines Overhaul Considerations
3126E and 3126B Commercial and Truck Engines Caterpillar Driver Information Display
3406E, C-10, C-12, C-15, C-16 Truck Engines Model View Illustrations
3208 Marine Engine Engine Air Cleaner Element (Foam) - Clean/Replace
3176C and 3196 Industrial Engines Turbocharger
3306C Truck Engine Engine Oil Pump - Remove
3126 Truck Engine (Military) Before Starting Engine