Window Wiper and Wiper Motor (Rear) - Remove and Install
- Disconnect harness assembly (1). Open cover (2).
Show/hide table
Illustration 2 g06269844 - Remove nut (3), lock washer (4), and wiper arm assembly (5).
Show/hide table
Illustration 3 g06269846 - Remove screw (6) and cover (7).
Show/hide table
Illustration 4 g06269847 Show/hide tableIllustration 5 g06269848 - Disconnect harness assembly (9).
- Support wiper motor assembly (8). Remove wiper cap (12), nut (11), cap nut (10), and wiper motor assembly (8).
Show/hide table
Illustration 1 | g06269842 |
- Install the wiper motor assembly and the wiper arm assembly in the reverse order of removal.
- Use the following torque to tighten cap nut (10):
1. If mounted on glass, tighten cap nut (10) to
6.5 ± 0.5 N·m (57.5 ± 4.4 lb in) .2. If mounted on steel, tighten cap nut (10) to
7.5 ± 0.5 N·m (66.4 ± 4.4 lb in) . - Use the following torque to tighten nut (11):
1. If mounted on glass, tighten nut (11) to
5.5 ± 0.5 N·m (48.7 ± 4.4 lb in) .2. If mounted on steel, tighten nut (11) to
9 ± 1 N·m (80 ± 9 lb in) . - Use the following tightening procedure during the wiper arm assembly installation:
1. Tighten nut (3) to
21 ± 1 N·m (186 ± 9 lb in) .2. Wait for minimum 0.5 hour to maximum 4 hours.
3. Again, tighten nut (3) to
21 ± 1 N·m (186 ± 9 lb in) .Field torque check:
Tighten nut (3) to
12 N·m (106 lb in) minimum.
- Use the following torque to tighten cap nut (10):
Caterpillar Information System:
986K Wheel Loader Machine Systems Oil Filter (Implement Pump Case Drain) - Remove and Install
24 Motor Grader Power Train Transfer Gears - Disassemble - Output
730,735 and 730 EJECTOR Articulated Truck Systems Pressure Sensor - HVAC
986K Wheel Loader Machine Systems Tilt Position Sensor and Mounting (Worktool Positioner Control) - Remove and Install
New Software is Now Used on Certain M Series Motor Graders {7620} New Software is Now Used on Certain M Series Motor Graders {7620}
986K Wheel Loader Machine Systems Oil Filter (Implement Pilot) (Front Pump Drive) - Remove and Install
The Crankcase Breather for the Engine is Relocated {1107} The Crankcase Breather for the Engine is Relocated {1107}
794AC C175 Engine Generator Lifting Group {0599, 0629, 0632, 0701, 1000} 794AC C175 Engine Generator Lifting Group {0599, 0629, 0632, 0701, 1000}
Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D7R II Track Type Tractor Cab Mounted Components - Remove and Install
Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D7R II Track Type Tractor Roof Mounted Components - Remove and Install
AP600F Asphalt Paver Feeder Control Sensor
Tube Assembly For the Boom Load Control Valve May Crack on Certain Material Handlers and Wheeled Excavators {5057, 5067} Tube Assembly For the Boom Load Control Valve May Crack on Certain Material Handlers and Wheeled Excavators {5057, 5067}
Improved Lift Arms Now Used on R3000H Load Haul Dump Machines {6119} Improved Lift Arms Now Used on R3000H Load Haul Dump Machines {6119}
BD118 and BD121 Side Discharge Bucket Safety Messages
BD118 and BD121 Side Discharge Bucket Plate Locations and Film Locations
BD118 and BD121 Side Discharge Bucket Declaration of Conformity
785G Off-Highway Truck Machines Systems Oil Filter (Brake) - Remove and Install
Parts Required for Attaching Improved Pilot Oil Accumulator Group to Pilot Lines Group on Certain Compact Wheel Loaders and Integrated Tool carrier {5077} Parts Required for Attaching Improved Pilot Oil Accumulator Group to Pilot Lines Group on Certain Compact Wheel Loaders and Integrated Tool carrier {5077}
C7.1 Industrial Engine Engine Air Cleaner Element - Replace
Hystat Performance Issues in Extreme Cold on Certain 914G/G2, IT14G2 Compact Wheel Loaders, and IT14 Integrated Toolcarriers {4350, 5057} Hystat Performance Issues in Extreme Cold on Certain 914G/G2, IT14G2 Compact Wheel Loaders, and IT14 Integrated Toolcarriers {4350, 5057}
Installation Procedure for Upgraded Extender Deflectors and Main Frame End Caps on Certain SE60V. {6631, 6641, 7051} Installation Procedure for Upgraded Extender Deflectors and Main Frame End Caps on Certain SE60V. {6631, 6641, 7051}
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Radio
Procedure To Install 3D Grade Control Harness On Certain Cold Planers {1408} Procedure To Install 3D Grade Control Harness On Certain Cold Planers {1408}
A New 3D Grade Control Harness is Now Used for Certain Cold Planers Machines {1408} A New 3D Grade Control Harness is Now Used for Certain Cold Planers Machines {1408}