Engine Oil Cooler - Remove and Install
- Remove oil filter (2). Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedure.
- Disconnect hose (1).
Show/hide table
Illustration 2 g02858919 - Remove joint screw (3). Remove oil cooler (4).
Show/hide table
Illustration 3 g02858921 - Remove seal (5) from oil cooler (4).
Show/hide table
Illustration 1 | g02798327 |
- Install oil cooler (4) in the reverse order of removal.
- Tighten joint screw (3) to a torque of
42 N·m ± 2 N·m (31 ± 2 lb ft) . - Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedure.
- Tighten joint screw (3) to a torque of
Caterpillar Information System:
14M3 Motor Grader Power Train Service Brake (Wheel Spindle) - Remove and Install
A New Single Speed Drive Motor is Used on Certain Skid Steer Loaders {4351, 5058} A New Single Speed Drive Motor is Used on Certain Skid Steer Loaders {4351, 5058}
797F ECM Configurable Parameters {1901, 4800, 4808, 5701, 7490, 7494, 7601, 7603, 7610, 7620} 797F ECM Configurable Parameters {1901, 4800, 4808, 5701, 7490, 7494, 7601, 7603, 7610, 7620}
CB64B, CB66B, and CB68B Propel System Joystick Control
MH3037 Material Handler Machine System Specification Lift Position Sensor and Mounting
Improved Sliding Frame Group is Now Used on Certain 424B and 424BHD Backhoe Loaders {5804, 6508} Improved Sliding Frame Group is Now Used on Certain 424B and 424BHD Backhoe Loaders {5804, 6508}
CB64B, CB66B, and CB68B Propel System Joystick Control
C3.8 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
CB64B, CB66B and CB68B Asphalt Compactor Machine Systems Gear Pump (Steering)
725C, 725C2, 730C and 730C2 Articulated Truck Systems Location of Components (Hydraulic System)
CB64B, CB66B, and CB68B Propel System Position Sensor
A New Fill Tube Cover for the Diesel Emissions Fluid (DEF) Tank is Now Available for Certain 770G and 772G Off-Highway Trucks {108T} A New Fill Tube Cover for the Diesel Emissions Fluid (DEF) Tank is Now Available for Certain 770G and 772G Off-Highway Trucks {108T}
MH3037 Material Handler Machine System Specification Lift Position Sensor and Mounting
C3.8 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
14M3 Motor Grader Power Train Service Brake (Wheel Spindle) - Disassemble
14M Motor Grader Power Train Service Brake (Wheel Spindle) - Assemble
New Connectors Are Used on Certain C-Series Knuckleboom Loader Stabilizer Lines {5057} New Connectors Are Used on Certain C-Series Knuckleboom Loader Stabilizer Lines {5057}
C3.8 Engines for Caterpillar Built Machines Water Pump - Remove and Install
A New Fuel Cooler System Is Now Available for Certain PM-200 Cold Planers {1274} A New Fuel Cooler System Is Now Available for Certain PM-200 Cold Planers {1274}
Procedure to Install the Fuel Cooler System on certain PM-200 Cold Planers {1712} Procedure to Install the Fuel Cooler System on certain PM-200 Cold Planers {1712}
MH3027 Material Handler C7.1 Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
730C and 730C2 EJECTOR Articulated Truck Systems Calibrations (Cat ET)
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic and Machine Systems Transmission Oil Cooler
AP555F Asphalt Paver Propel System Machine Preparation for Testing and Adjusting