Engine Oil Pump - Remove and Install
Start By:
- Remove the front housing.
- Remove screws (1). Remove oil pump cover (2).
Show/hide table
Illustration 2 g02860156 - Remove oil pump rotors (3).
Show/hide table
| |
| Illustration 1 | g02797922 |
- Install the engine oil pump in the reverse order of removal.
- Tighten screws (1) to a torque of
8.6 ± 0.7 N·m (76.1 ± 6.2 lb in) .
- Tighten screws (1) to a torque of
End By:
- Install the front housing.
Caterpillar Information System:
MH3037 Material Handler Machine System Specification Lift Position Sensor and Mounting
C3.8 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
14M3 Motor Grader Power Train Service Brake (Wheel Spindle) - Remove and Install
A New Single Speed Drive Motor is Used on Certain Skid Steer Loaders {4351, 5058} A New Single Speed Drive Motor is Used on Certain Skid Steer Loaders {4351, 5058}
797F ECM Configurable Parameters {1901, 4800, 4808, 5701, 7490, 7494, 7601, 7603, 7610, 7620} 797F ECM Configurable Parameters {1901, 4800, 4808, 5701, 7490, 7494, 7601, 7603, 7610, 7620}
CB64B, CB66B, and CB68B Propel System Joystick Control
MH3037 Material Handler Machine System Specification Lift Position Sensor and Mounting
Improved Sliding Frame Group is Now Used on Certain 424B and 424BHD Backhoe Loaders {5804, 6508} Improved Sliding Frame Group is Now Used on Certain 424B and 424BHD Backhoe Loaders {5804, 6508}
CB64B, CB66B, and CB68B Propel System Joystick Control
C3.8 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
CB64B, CB66B and CB68B Asphalt Compactor Machine Systems Gear Pump (Steering)
725C, 725C2, 730C and 730C2 Articulated Truck Systems Location of Components (Hydraulic System)
14M3 Motor Grader Power Train Service Brake (Wheel Spindle) - Disassemble
14M Motor Grader Power Train Service Brake (Wheel Spindle) - Assemble
New Connectors Are Used on Certain C-Series Knuckleboom Loader Stabilizer Lines {5057} New Connectors Are Used on Certain C-Series Knuckleboom Loader Stabilizer Lines {5057}
C3.8 Engines for Caterpillar Built Machines Water Pump - Remove and Install
A New Fuel Cooler System Is Now Available for Certain PM-200 Cold Planers {1274} A New Fuel Cooler System Is Now Available for Certain PM-200 Cold Planers {1274}
Procedure to Install the Fuel Cooler System on certain PM-200 Cold Planers {1712} Procedure to Install the Fuel Cooler System on certain PM-200 Cold Planers {1712}
MH3027 Material Handler C7.1 Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
730C and 730C2 EJECTOR Articulated Truck Systems Calibrations (Cat ET)
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic and Machine Systems Transmission Oil Cooler
AP555F Asphalt Paver Propel System Machine Preparation for Testing and Adjusting
AP555F Asphalt Paver Propel System Piston Pump Flow - Test
AP555F Asphalt Paver Propel System Piston Pump Neutral - Test and Adjust - Left Propel