Service Brake (Wheel Spindle) - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 439-3940 | Bracket As | 2 |
B | 1P-2420 | Transmission Repair Stand | 1 |
C | 140-7742 | Sleeve | 2 |
D | 154-6181 | Forcing Bolt | 2 |
E | 8B-7551 | Bearing Puller Gp | 1 |
Start By:
- Remove the service brake (wheel spindle).
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
- Use Tooling (A), Tooling (C), and a suitable lifting device to position service brake (1) onto Tooling (B). The weight of service brake (1) is approximately
272 kg (600 lb) .Show/hide tableIllustration 2 g01349321 - Remove bolts (2). Remove retainer (3).
Show/hide table
Illustration 3 g01349338 - Remove shims (4). Use Tooling (C) and a suitable lifting device to remove sprocket (5). The weight of sprocket (5) is approximately
36 kg (80 lb) .Note: Note the quantity and the order of shims (4).
Show/hide tableIllustration 4 g06048304 Show/hide tablePersonal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Remove bolts (6).
Show/hide table
Illustration 5 g01349339 Show/hide tableIllustration 6 g01349519 - Remove O-ring seal (7). Use Tooling (D) to remove bearing cone (8). Use Tooling (A) and a suitable lifting device to remove cover (9). The weight of cover (9) is approximately
42 kg (93 lb) .Show/hide tableIllustration 7 g06048314 - Remove bearing cup (10) from cover (9).
Show/hide table
Illustration 8 g06048320 - Remove springs (11). Remove plates (12) and discs (13).
Note: Note the quantity and the order of plates (12) and discs (13).
Show/hide table
Illustration 1 | g01349310 |
- Remove piston (14). Remove spacers (15). Remove hub (16).
Show/hide table
Illustration 10 g01349359 - Remove seals (17) from piston (14).
Show/hide table
Illustration 11 g01349430 - Use Tooling (A) to remove housing (18). The weight of housing (18) is approximately
77 kg (170 lb) . Position housing (18) onto suitable blocking.Show/hide tableIllustration 12 g01349436 - Remove the first half of Duo-Cone seal (19). Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Remove". Remove bearing cup (20).
Show/hide table
Illustration 13 g01349462 - Remove the second half of Duo-Cone seal (19). Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Remove".
Show/hide table
Illustration 14 g01349453 - Use Tooling (E) to remove bearing cone (21).
Show/hide table
Illustration 15 g01378162 - Remove spacer (22).
Show/hide table
Illustration 9 | g06048340 |
Caterpillar Information System:
C3.8 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
MH3037 Material Handler Machine System Specification Lift Position Sensor and Mounting
C3.8 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
14M3 Motor Grader Power Train Service Brake (Wheel Spindle) - Remove and Install
A New Single Speed Drive Motor is Used on Certain Skid Steer Loaders {4351, 5058} A New Single Speed Drive Motor is Used on Certain Skid Steer Loaders {4351, 5058}
797F ECM Configurable Parameters {1901, 4800, 4808, 5701, 7490, 7494, 7601, 7603, 7610, 7620} 797F ECM Configurable Parameters {1901, 4800, 4808, 5701, 7490, 7494, 7601, 7603, 7610, 7620}
CB64B, CB66B, and CB68B Propel System Joystick Control
MH3037 Material Handler Machine System Specification Lift Position Sensor and Mounting
Improved Sliding Frame Group is Now Used on Certain 424B and 424BHD Backhoe Loaders {5804, 6508} Improved Sliding Frame Group is Now Used on Certain 424B and 424BHD Backhoe Loaders {5804, 6508}
CB64B, CB66B, and CB68B Propel System Joystick Control
C3.8 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
CB64B, CB66B and CB68B Asphalt Compactor Machine Systems Gear Pump (Steering)
14M Motor Grader Power Train Service Brake (Wheel Spindle) - Assemble
New Connectors Are Used on Certain C-Series Knuckleboom Loader Stabilizer Lines {5057} New Connectors Are Used on Certain C-Series Knuckleboom Loader Stabilizer Lines {5057}
C3.8 Engines for Caterpillar Built Machines Water Pump - Remove and Install
A New Fuel Cooler System Is Now Available for Certain PM-200 Cold Planers {1274} A New Fuel Cooler System Is Now Available for Certain PM-200 Cold Planers {1274}
Procedure to Install the Fuel Cooler System on certain PM-200 Cold Planers {1712} Procedure to Install the Fuel Cooler System on certain PM-200 Cold Planers {1712}
MH3027 Material Handler C7.1 Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
730C and 730C2 EJECTOR Articulated Truck Systems Calibrations (Cat ET)
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic and Machine Systems Transmission Oil Cooler
AP555F Asphalt Paver Propel System Machine Preparation for Testing and Adjusting
AP555F Asphalt Paver Propel System Piston Pump Flow - Test
AP555F Asphalt Paver Propel System Piston Pump Neutral - Test and Adjust - Left Propel
Improved Upper Articulation Pin Now Used on R2900G and R3000H Load Haul Dump Machines {7057, 7100} Improved Upper Articulation Pin Now Used on R2900G and R3000H Load Haul Dump Machines {7057, 7100}