Transmission Hydraulic Control Valve - Remove and Install
开始:
- 拆下后曲轴箱护罩。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 将变速箱油排入合适的容器中。
Show/hide table
图 1 g03865537 - 断开软管组件 (3)。 拆下螺栓和垫圈 (1)。 拆下油底壳 (2)。
Show/hide table
图 2 g03865577 - 拆下将吸油管 (4) 连接到歧管的螺栓 (6)。
- 拆下螺栓 (4) 和垫圈。
- 拆下吸油管组件 (6) 和 O 形密封圈。
- 拆下管组件 (5) 和 O 形密封圈。
Show/hide table
图 3 g03865611 - 断开线束组件 (10)。
- 拆下变速箱控制阀 (8) 和 O 形密封圈。
- 拆下主安全阀 (9) 和 O 形密封圈。
Show/hide table
图 4 g03865670 主安全阀 - 拆下 O 形密封圈 (11) 和密封圈 (14)。 拆下螺母 (13) 和线圈组件 (12)。
Show/hide table
图 5 g03865636 - 拆卸螺栓 (15) 和垫圈。 拆下歧管 (16) 和密封垫。
- 从歧管 (16) 上拆下阀 (17) 和 (18) 以及 O 形密封圈。
Show/hide table
图 6 g03865648 - 拆下电缆扎带 (20) 并将线束组件 (10) 放到一旁。
- 拆下螺栓 (19) 和垫圈。
- 拆下板 (21) 和密封垫。
- 按与拆卸相反的顺序安装变速箱液压控制装置 (8)。
- 使用所密封的润滑剂润滑变速箱液压控制阀 (8) 和主安全阀 (9) 的孔。
- 拧紧变速箱液压控制阀 (8) 的螺栓至扭矩为
3.7 ± 0.8 N·m (33.0 ± 7.0 lb in) 。 - 拧紧螺母 (13) 至扭矩为
6.1 ± 0.7 N·m (54 ± 6.0 lb in) 。 - 将主安全阀 (9) 拧紧至扭矩为
100 ± 10 N·m (74 ± 7 lb ft) 。 - 使用所密封的润滑剂润滑阀 (17) 和 (18) 的孔。
- 使用所密封的润滑剂润滑管组件 (5) 的孔。
Caterpillar Information System:
994K Wheel Loader Machine Systems Transmission Planetary
AP500F Asphalt Paver Propel System Relief Valve (Charge) - Test and Adjust - Left Propel
SE34 V and SE34 VT Asphalt Screeds Plate Locations and Film Locations
SE34 V and SE34 VT Asphalt Screeds Specifications
SE34 V and SE34 VT Asphalt Screeds Safety Messages
740 GC, 740 Ejector, 745 Articulated Truck Power Train Speed Sensor (Transmission) - Remove and Install
415F2 Industrial Loader Maintenance Interval Schedule
740 GC, 740 Ejector, 745 Articulated Truck Machine System Front Suspension Cylinder - Remove and Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Rear Axle - Remove and Install
C3.4B Engines ECM Software - Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Disassemble
CCS7 Combination Vibratory Compactors Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
Updated LSI Installation And Calibration Procedure On Certain Telehandlers {1408, 1439} Updated LSI Installation And Calibration Procedure On Certain Telehandlers {1408, 1439}
R1600G Underground Load Haul Dump Machine Repower With C11 Engine {1000, 7000} R1600G Underground Load Haul Dump Machine Repower With C11 Engine {1000, 7000}
SE34 V and SE34 VT Asphalt Screeds Thickness Control Screw Adjustment
415F2 Industrial Loader Monitoring System
SE34 V and SE34 VT Asphalt Screeds Lifting and Tying Down the Machine
415F2 Industrial Loader Towing the Machine
2015/07/27 Improved Bracket Clearance with Fuel Tank Is Now Available For Certain 797FOff-Highway Trucks {7050, 7050}
SE34 V and SE34 VT Asphalt Screeds Access Doors and Covers
CW16 Pneumatic Compactor Machine Systems Axle (Front) - Remove and Install
SE34 V and SE34 VT Asphalt Screeds Screed - Lubricate
Dealer Services Portal Provides No Feedback on Subscription Requests or Successes{7606} Dealer Services Portal Provides No Feedback on Subscription Requests or Successes{7606}
MD6200 Rotary Drill Air Compressor Oil Separator Filter - Replace - High Pressure - If Equipped