Rear Axle - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 386-6030 | 杠杆式拉拔举倾机构总成 | 1 |
B | 366-6003 | 变矩器搬运组件 | 1 |
C | 439-3939 | 连杆支架组件 | 2 |
D | 138-7573 | 连杆支架 | 1 |
E | 138-7575 | 连杆支架 | 1 |
F | 189-0408 | 钩环组件 | 1 |
开始:
- 拆下后轮胎。
Show/hide table
吊装或垫塞不当可能会造成人员伤亡。 当使用起重机或千斤顶顶升任何零件或部件时,与之保持距离。 确保起重机或千斤顶具备正确的部件吊装能力。 在沉重部件下面进行任何工作之前先安装垫块或台架。 图上显示的是部件的近似重量。 清洁要安装零件的所有表面。 |
Show/hide table
带载的传动系拧紧扭矩可造成人身伤害。 不等的车轮转速可产生传动系拧紧扭矩,从而使传动系部件在拆解中带载。 拆解前,务必释放传动系拧紧扭矩。 |
- 拆下护罩 (1)、 (2) 和 (3)。
Show/hide table
图 2 g03865467 - 断开管 (4) 和管 (6)。 断开线束组件 (5)。
Show/hide table
图 3 g03865472 - 拆下螺栓 (7),并由两个人将传动轴 (8) 降到适当的支座上。 传动轴 (8) 的重量约为
43.09105 kg (95 lb) 。Show/hide table图 4 g03865474 - 断开软管组件 (9)、软管组件 (10) 和软管组件 (11)。
Show/hide table
图 5 g03865540 - 拆下螺母 (13) 和螺栓。 拆下螺母 (14) 和螺栓。 拆下后稳定杆 (12)。
Show/hide table
图 6 g03865542 - 将工具 (A) 连接到后悬架总成 (13) 和后机架悬架 (14) 的后半部。
Show/hide table
图 7 g03865543 - 将工具 (C) 和适当的起吊设备安装到后车桥组件 (15) 上。 后车桥组件 (15) 的重量约为
2177 kg (4800 lb) 。 对后车桥组件 (15) 的另一侧重复该步骤Show/hide table图 8 g03865659 - 将工具 (D)、 (E) 和 (F) 安装到轭组件 (16) 上。 这样可以防止后桥组件向下转动。
Show/hide table
图 9 g03865628 - 拆下螺栓 (18),然后由两个人拆下支架 (17)。 支架 (17) 的重量约为
34 kg (75 lb) 。Show/hide table图 10 g03865627 - 拆下螺栓 (19)。
Show/hide table
图 11 g03865775 - 使用工具 (C) 和适当的起吊设备将后桥组件 (15) 降到工具 (B) 上。
Show/hide table
图 1 | g03865465 |
- 按与拆卸相反的顺序安装后桥组件 (10)。
- 拧紧螺栓 (7) 至扭矩为
117 ± 10 N·m (86 ± 7 lb ft) 。
- 拧紧螺栓 (7) 至扭矩为
Caterpillar Information System:
C3.4B Engines ECM Software - Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Disassemble
CCS7 Combination Vibratory Compactors Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
773E Off-Highway Truck Hydraulic System Control Valve (Hoist)
New Onboard Radio Wiring Group Now Available on CAT Command for Underground Equipped Machines {1408, 733T} New Onboard Radio Wiring Group Now Available on CAT Command for Underground Equipped Machines {1408, 733T}
CCS7 Combination Vibratory Compactors Machine Systems Metering Pump (Steering) - Remove and Install
MH3037 Material Handler Stopping the Engine
2015/07/20 New Clamps are now Used in the Water Lines Group on Certain 14M Motor Graders {1380}
2015/09/11 Improved Seals are Now Used in the Hoist Valve on Certain Off-Highway Trucks {5051}
SE34 V and SE34 VT Asphalt Screeds Maintenance Interval Schedule
794 AC Off-Highway Truck Field Assembly Films - Install
16M3 and 18M3 Motor Graders Information Display Diagnostic Capabilities
740 GC, 740 Ejector, 745 Articulated Truck Machine System Front Suspension Cylinder - Remove and Install
415F2 Industrial Loader Maintenance Interval Schedule
740 GC, 740 Ejector, 745 Articulated Truck Power Train Speed Sensor (Transmission) - Remove and Install
SE34 V and SE34 VT Asphalt Screeds Safety Messages
SE34 V and SE34 VT Asphalt Screeds Specifications
SE34 V and SE34 VT Asphalt Screeds Plate Locations and Film Locations
AP500F Asphalt Paver Propel System Relief Valve (Charge) - Test and Adjust - Left Propel
994K Wheel Loader Machine Systems Transmission Planetary
740 GC, 740 Ejector, 745 Articulated Truck Power Train Transmission Hydraulic Control Valve - Remove and Install
Updated LSI Installation And Calibration Procedure On Certain Telehandlers {1408, 1439} Updated LSI Installation And Calibration Procedure On Certain Telehandlers {1408, 1439}
R1600G Underground Load Haul Dump Machine Repower With C11 Engine {1000, 7000} R1600G Underground Load Haul Dump Machine Repower With C11 Engine {1000, 7000}
SE34 V and SE34 VT Asphalt Screeds Thickness Control Screw Adjustment