Differential and Bevel Gear (Front and Rear) - Disassemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7502 | 修理台架 | 1 |
B | 439-3938 | 连杆支架 | 2 |
C | 456-4371 | 操纵杆式起重机 | 1 |
D | 1P-5546 | 十字挡块 | 1 |
E | 6V-3160 | 双作用油缸 | 1 |
F | 1P-0520 | 冲头总成 | 1 |
H | 6V-4070 | 活动扳手 | 1 |
J | 8B-7551 | 轴承拉拔器 | 1 |
K | 5F-7343 | 轴承拉拔器总成 | 1 |
开始:
- 拆下前或后差速器组件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在所有壳体和箱体组件上做好位置标记,以便于组装。
Show/hide table
图 1 g03865438 - 将工具 (B) 和适当的起吊设备连接到差速器和伞齿轮组件 (1) 上。 差速器和伞齿轮组件 (1) 的重量约为
322 kg (710 lb) 。Show/hide table图 2 g03865440 - 定位差速器和伞齿轮组件 (1) 并将其放置到工具 (A) 上。 拆下工具 (B) 和相应的起吊设备。
Show/hide table
图 3 g03865449 - 将差速器和伞齿轮组件 (1) 转动 90 度。
Show/hide table
图 4 g03865468 - 将工具 ( C )和适当的起吊设备连接到轭上。 小齿轮壳体 (3) 的重量约为
75 kg (165 lb) 。 拆下螺栓 (2 )。Show/hide table图 5 g03865471 - 将两个螺栓 (2) 安装到小齿轮壳体的螺纹孔中(顶出螺栓孔)。 通过均匀上紧两个螺栓 (2) 分离小齿轮壳体 (3)。 拆下小齿轮壳体 (3)。
Show/hide table
图 6 g03865526 - 卸下垫片 (4)。
Show/hide table
图 7 g03865544 - 拆下 O 形密封圈 (5)。
Show/hide table
图 8 g03865553 - 将小齿轮壳体定位到适当的支座上。
- 拆下螺栓 (6) 和护圈 (7)。
Show/hide table
图 9 g03865904 - 拆下 O 形密封圈 (8) 和唇形密封 (9)。
Show/hide table
图 10 g03865905 - 拆下挡圈 (10) 和锁紧垫圈 (11)。
Show/hide table
图 11 g03865906 - 使用工具 (H)(未显示)拆下锁紧螺母 (12)。 拆下锁紧螺母 (12) 和开口垫圈 (13)。
Show/hide table
图 12 g03865972 - 使用适当的压具将小齿轮轴 (14) 从轴承内圈 (15) 上拆下。
Show/hide table
图 13 g03865973 - 拆下轴承内圈 (15)。
Show/hide table
图 14 g03865974 典型示例 - 使用适当的压具和工具 (J)(未显示)拆下轴承外圈 (16)。
Show/hide table
图 15 g03865975 - 拆下轴承外圈 (17) 和轴承外圈 (17a)。
Show/hide table
图 16 g03865976 - 在工具 (A) 上旋转托架和差速器组件 90 度。
- 拆下四个螺栓 (18) 和防护罩 (19)。
Show/hide table
图 17 g03865999 - 利用适当的起吊设备将托架和差速器组件定位到工具 (A) 上。 托架和差速器组件的重量约为
234 kg (516 lb) 。 - 在工具 (A) 上额外旋转托架和差速器组件 90 度。
Show/hide table
图 18 g03866003 - 拆下螺栓 (20) 和锁 (21)。 对另一侧重复此操作。
Show/hide table
图 19 g03866009 不要从托架和差速器组件上拆下适当的起吊设备。 - 拆下调整环 (22)。 对另一侧重复此操作。
Show/hide table
图 20 g03866014 - 拆下螺栓 (23) 和轴承盖 (24)。
Show/hide table
图 21 g03866037 - 卸下轴承外圈 (25)。
Show/hide table
图 22 g03866038 - 使用适当的起吊设备将差速器组件和伞齿轮 (26) 从托架组件 (27) 拆下。 差速器组件和伞齿轮 (26) 的重量约为
115 kg (254 lb) 。Show/hide table图 23 g03866235 - 将轴承 (26a) 从托架组件 (27) 上拆下。 拆下轴承座圈 (26b)。
Show/hide table
图 24 g03866236 Show/hide table图 25 g03866237 - 施加气压,以便将离合器活塞 (27a) 从托架组件 (27) 上拆下。 拆下离合器活塞 (27a)。
Show/hide table
图 26 g03868985 - 将 D 形密封圈 (27b) 和 (27c) 从离合器活塞 (27a) 上拆下。
Show/hide table
图 27 g03866087 - 将差速器组件和伞齿轮定位到适当的支座上。
- 拆下轴承外圈 (28) 和 O 形密封圈 (32)。
- 拆下止推环 (29)。
- 拆下螺栓 (30) 和顶部离合器壳体 (31)。
Show/hide table
图 28 g03866094 - 将止推垫圈 (33) 从顶部离合器壳体 (31) 的背侧拆下。
Show/hide table
图 29 g03866103 - 拆下止推板 (34)。
Show/hide table
图 30 g03866114 - 拆下弹簧 (35)、摩擦盘 (36) 和隔板 (37)。
Show/hide table
图 31 g03866119 - 拆下齿轮 (38)、螺栓 (40),然后分离壳体 (39)
Show/hide table
图 32 g03870565 - 拆下弹簧销 (46c)。 拆下螺栓 (46)。 将伞齿轮 (46a) 从差速器壳体 (46b) 上拆下。
Show/hide table
图 33 g03866124 - 拆下十字轴齿轮组件 (41)。
Show/hide table
图 34 g03866131 - 拆下止推垫圈 (42) 和齿轮 (43)。
Show/hide table
图 35 g03870010 - 将齿轮套筒 (43a) 从十字轴 (43b) 上拆下。
Show/hide table
图 36 g03866169 - 拆下齿轮 (44)。
Show/hide table
图 37 g03866175 - 拆下止推垫圈 (45)。
Show/hide table
图 38 g03866231 - 拆下滚销 (47) 和伞齿轮 (48)。
Caterpillar Information System:
CCS7 Combination Vibratory Compactors Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
773E Off-Highway Truck Hydraulic System Control Valve (Hoist)
New Onboard Radio Wiring Group Now Available on CAT Command for Underground Equipped Machines {1408, 733T} New Onboard Radio Wiring Group Now Available on CAT Command for Underground Equipped Machines {1408, 733T}
CCS7 Combination Vibratory Compactors Machine Systems Metering Pump (Steering) - Remove and Install
MH3037 Material Handler Stopping the Engine
2015/07/20 New Clamps are now Used in the Water Lines Group on Certain 14M Motor Graders {1380}
2015/09/11 Improved Seals are Now Used in the Hoist Valve on Certain Off-Highway Trucks {5051}
SE34 V and SE34 VT Asphalt Screeds Maintenance Interval Schedule
794 AC Off-Highway Truck Field Assembly Films - Install
16M3 and 18M3 Motor Graders Information Display Diagnostic Capabilities
16M3 and 18M3 Motor Graders Information Display General Information
16M3 and 18M3 Motor Graders Information Display Service Tools
C3.4B Engines ECM Software - Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Rear Axle - Remove and Install
740 GC, 740 Ejector, 745 Articulated Truck Machine System Front Suspension Cylinder - Remove and Install
415F2 Industrial Loader Maintenance Interval Schedule
740 GC, 740 Ejector, 745 Articulated Truck Power Train Speed Sensor (Transmission) - Remove and Install
SE34 V and SE34 VT Asphalt Screeds Safety Messages
SE34 V and SE34 VT Asphalt Screeds Specifications
SE34 V and SE34 VT Asphalt Screeds Plate Locations and Film Locations
AP500F Asphalt Paver Propel System Relief Valve (Charge) - Test and Adjust - Left Propel
994K Wheel Loader Machine Systems Transmission Planetary
740 GC, 740 Ejector, 745 Articulated Truck Power Train Transmission Hydraulic Control Valve - Remove and Install
Updated LSI Installation And Calibration Procedure On Certain Telehandlers {1408, 1439} Updated LSI Installation And Calibration Procedure On Certain Telehandlers {1408, 1439}