Films - Install
Parts and Specification Information
Show/hide table
Illustration 1 | g03865195 |
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
Show/hide table
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information. |
Show/hide table
Item | Part Number | Description | Qty | Specification | Approximate Weight |
1 | 450-6701 | Film | 1 | ||
2 | 299-7935 | Film | 1 | ||
3 | 450-6702 | Film | 1 | ||
4 | 450-6703 | Film | 1 | ||
5 | 279-9304 | Film | 1 | ||
6 | 450-6704 | Film | 1 |
- Install film (1) on the center of the front radiator.
- Install film (2)
170 mm (6.7 inch) from the bottom of the canopy and50 mm (2 inch) from the angle. - Install film (3) on the left side of the body
30 mm (1.2 inch) from the top and side. - Install film (4) on the right side of the body
30 mm (1.2 inch) from the top and side.Show/hide tableIllustration 3 g03865239 (E) 210 mm (8.25 inch)
(F)10 mm (0.4 inch)
(G)110 mm (4.3 inch)
(H)10 mm (0.4 inch) - Install film (5) to the side of the cab
110 mm (4.3 inch) from the edge of the door and210 mm (8.25 inch) from the bottom. - Install film (6) to the side of the cab
10 mm (0.4 inch) from the bottom and side.
Show/hide table
Illustration 2 | g03865205 |
(A) (B) (C) (D) |
Note: Insure all surfaces are clean and free of dirt or debris before applying films.
Caterpillar Information System:
16M3 and 18M3 Motor Graders Information Display Diagnostic Capabilities
16M3 and 18M3 Motor Graders Information Display General Information
16M3 and 18M3 Motor Graders Information Display Service Tools
CCS7 Combination Vibratory Compactors Machine Systems Direction and Speed Control - Remove and Install
MH 3037 Material Handler Cab Riser Control
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Neutralizer Valve - Check and Adjust
2015/07/21 Improved Differential Filter Hose is Now Used on Certain 793F Off-Highway Trucks {3016, 3067}
740 GC, 740 Ejector, 745 Articulated Truck Power Train Tire and Rim - Remove and Install
A New Torque Specification for the Track Bolts is Now used on Certain Hydraulic Excavators and Track Feller Bunchers {4170} A New Torque Specification for the Track Bolts is Now used on Certain Hydraulic Excavators and Track Feller Bunchers {4170}
CB64B, CB66B and CB68B Asphalt Compactors Machine Electronic Control System Actuator - Test
2015/07/21 An Alternate Coolant Sampling Port Location is Now Available on Certain 14M and 16M Motor Graders {1378}
24 Motor Grader Specifications
SE34 V and SE34 VT Asphalt Screeds Maintenance Interval Schedule
2015/09/11 Improved Seals are Now Used in the Hoist Valve on Certain Off-Highway Trucks {5051}
2015/07/20 New Clamps are now Used in the Water Lines Group on Certain 14M Motor Graders {1380}
MH3037 Material Handler Stopping the Engine
CCS7 Combination Vibratory Compactors Machine Systems Metering Pump (Steering) - Remove and Install
New Onboard Radio Wiring Group Now Available on CAT Command for Underground Equipped Machines {1408, 733T} New Onboard Radio Wiring Group Now Available on CAT Command for Underground Equipped Machines {1408, 733T}
773E Off-Highway Truck Hydraulic System Control Valve (Hoist)
CCS7 Combination Vibratory Compactors Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Disassemble
C3.4B Engines ECM Software - Install
740 GC, 740 Ejector, 745 Articulated Truck Power Train Rear Axle - Remove and Install
740 GC, 740 Ejector, 745 Articulated Truck Machine System Front Suspension Cylinder - Remove and Install