A SOS Port Can be Installed for Engine Oil Sampling on F2 Series Backhoe Loaders and Industrial Loaders Equipped with a C3.4 Engine {1306, 1308, 7542}
- Backhoe Loader
- 415F2 (S/N: HWA1-UP)
- 415F2 IL (S/N: PF41-UP)
- 427F2 (S/N: HWK1-UP)
- 415F2 IL (S/N: PF41-UP)
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.
Problem
F2 series Backhoe Loaders equipped with a C3.4 engine do not have an SOS Port for obtaining engine oil samples. Due to the size and shape of the dipstick tube, an engine oil sample is not possible through the tube.
Solution
Show/hide table
Illustration 1 | g03831451 |
Location to install (A) Engine Oil Filter |
An 8C-3345 Fluid Sampling Valve As can be installed to obtain the engine oil sample. Refer to Illustration 1.
Note: During installation of the sampling valve, apply Loctite 572 to the threads of the valve.
Caterpillar Information System:
CW34 Pneumatic Compactor Lifting and Tying Down the Machine
CW16 Pneumatic Compactor Ballast Information
CW34 Pneumatic Compactor Operation
415F2 and 427F2 Backhoe Loaders Engine Supplement Refrigerant Condenser - Remove and Install
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Diesel Fuel System Cleaner - Add
994K Wheel Loader Fuses - Replace
797F Off-Highway Truck Field Assembly Cooling System Package - Install
16M Series 3 and 18M Series 3 Motor Grader Systems Frame - Rear
C175-16 Engine for Off-Highway Trucks Engine Oil Level Sensor
2015/05/01 A New Special Instruction Is Available for Installation of Precleaner for Engine Air {1051, 1055}
C175-16 Engine for Off-Highway Truck/Tractors Thermocouple
C175-16 Engine for Off-Highway Truck/Tractors Inlet Manifold Air Pressure Sensor
CW34 Pneumatic Compactor Air Compressor Oil - Change
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Determining Diagnostic Trouble Codes
2015/05/14 Gear Inspection Should Be Performed When Replacing the Torsional Coupler on Certain 14M and 16M Motor Graders {3063}
CW34 Pneumatic Compactor Monitoring System
CB64B, CB66B and CB68B Asphalt Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
New Steering Cylinders With Position Sensors are Now Available on Certain Motor Graders {4303, 7620} New Steering Cylinders With Position Sensors are Now Available on Certain Motor Graders {4303, 7620}
527 Track-Type Skidder Reference Material
PL83 and PL87 Pipelayers Machine Systems Counterweight Cylinder - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Seat - Remove and Install
Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104} Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104}
Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117} Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117}
Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107} Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107}