Blade - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 1 |
B | 1u-9200 | Lever Puller Hoist | 1 |
C | 140-7742 | Sleeve | 2 |
- Raise blade assembly (1). Use suitable blocking in order to support blade assembly (1) and circle assembly (2) on both sides.
Show/hide table
Illustration 2 g01340956 - Loosen locknuts (3). Loosen setscrews (4). Repeat this step for the opposite side.
Show/hide table
Illustration 3 g01340856 - Remove cotter pin (5). Remove pin (6).
Show/hide table
Illustration 4 g01340967 - Use Tooling (A), Tooling (B), Tooling (C), and a suitable lifting device in order to pull blade assembly (1) from circle assembly (2).
Show/hide table
Illustration 5 g01340969 - Attach Tooling (C) and an additional suitable lifting device onto blade assembly (1). Remove blade assembly (1). The weight of blade assembly (1) is approximately
1492 kg (3289 lb) .
Show/hide table
Illustration 1 | g01340852 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 1 |
B | 1u-9200 | Lever Puller Hoist | 1 |
C | 140-7742 | Sleeve | 2 |
- Use Tooling (A), Tooling (B), Tooling (C), and two suitable lifting devices in order to position blade assembly (1) onto circle assembly (2). The weight of blade assembly (1) is approximately
1492 kg (3289 lb) . - Use Tooling (A) and Tooling (B) in order to pull blade assembly (1) into position.
Show/hide table
Illustration 8 g01340856 - Install pin (6). Install cotter pin (5).
Show/hide table
Illustration 9 g01340956 - Tighten setscrews (4) and locknuts (3) in order to obtain a clearance of
0.13 to 0.89 mm (0.005 to 0.035 inch) between the rails and the wear strips. In order to achieve the minimum clearance, sideshift the blade assembly through the full range.Show/hide tableIllustration 10 g01340852 - Remove the suitable blocking from blade assembly (1) and circle assembly (2). Lower blade assembly (1).
Show/hide table
Illustration 6 | g01341018 |
Show/hide table
Illustration 7 | g01341025 |
Caterpillar Information System:
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Articulation Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Accumulator (Blade Cushion) - Remove and Install
Improved Axles Are Available for Certain Vibratory Utility Compactors {7113} Improved Axles Are Available for Certain Vibratory Utility Compactors {7113}
2015/05/15 Sonic Sensor Kits Are Now Available on AP255E Asphalt Paver for the Conveyor and Auger {1408, 5657}
Procedure to Install Conveyor and Auger Sonic Sensors on AP255E, Paver {1408, 5657} Procedure to Install Conveyor and Auger Sonic Sensors on AP255E, Paver {1408, 5657}
Bench Test Procedure for 420F2, 426F2, 427F2, 428F2, 430F2, 432F2, 434F2, 440, 444F2, and 450 Backhoe Loader Transmissions {3030, 3073, 3139, 5051} Bench Test Procedure for 420F2, 426F2, 427F2, 428F2, 430F2, 432F2, 434F2, 440, 444F2, and 450 Backhoe Loader Transmissions {3030, 3073, 3139, 5051}
CW34 Pneumatic Compactor Cooling System Water Temperature Regulator - Replace
CW34 Pneumatic Compactor Cooling System Water Temperature Regulator - Replace
CW34 Pneumatic Compactor Cooling System Coolant Sample (Level 1) - Obtain
CW34 Pneumatic Compactor Cooling System Coolant Sample (Level 1) - Obtain
Field Installation Instructions for the 2-bolt to 3-bolt Fan Drive Upgrade on Certain 3500 Machines {1359, 7960} Field Installation Instructions for the 2-bolt to 3-bolt Fan Drive Upgrade on Certain 3500 Machines {1359, 7960}
2015/04/28 An Improved Speed Sensor Mounting Group Is Now Used on Certain 424B Backhoe Loaders {5736}
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Tip Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Arm - Remove
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Arm - Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Bottom Guard - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Brake Accumulator - Remove and Install
2015/04/30 An Improved Air Pressure Gauge For The Brakes Is Now Used On Certain K And K Series 2 Motor Graders {7450, 7451}
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Cab - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Cylinder - Remove and Install
CW34 Pneumatic Compactor Fuel System Primary Filter (Water Separator) - Replace
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Remove and Install
CW34 Pneumatic Compactor Fuel System Secondary Filter - Replace