Blade Lift Arm - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 4C-9634 | Puller Stud | 1 |
1P-1839 | Bearing Puller Adapter | 1 | |
1P-1836 | Bearing Puller Adapter | 1 | |
9U-6832 | Nut | 1 | |
6V-3170 | Double Acting Cylinder | 1 | |
3S-6224 | Electric Hydraulic Pump Gp | 1 | |
6V-4035 | Sleeve | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach a suitable lifting device to cylinder (1). The weight of cylinder (1) is approximately
91 kg (200 lb) . Remove bolts (2). Position cylinder (1) against the frame.Show/hide tableIllustration 2 g01379104 - Attach two suitable lifting devices onto arm assembly (3). The weight of arm assembly (3) is approximately
186 kg (410 lb) .Show/hide tableIllustration 3 g01379116 - Remove bolts (4) and lock (5).
Show/hide table
Illustration 4 g01379124 - Remove bolts (6) and plate (7).
Show/hide table
Illustration 5 g01379129 - Remove pin (8) and thrust washers (9).
Note: Note the order and the quantity of thrust washers (9).
Show/hide tableIllustration 6 g01379147 - Remove bolts (10) and lock (11).
Show/hide table
Illustration 7 g01379155 - Remove pin (12) and thrust washers (13).
Note: Note the order and the quantity of thrust washers (13).
Show/hide tableIllustration 8 g01379220 - Remove arm assembly (3).
Show/hide table
Illustration 9 g01379234 - Remove bolts (14) and retainer (15). Remove seal (17) and O-ring seal (16). Remove shims (18). Remove thrust washers (19).
Note: Note the quantity and the order of shims (18) and thrust washers (19).
Show/hide tableIllustration 10 g01379242 - Remove yoke (20). Remove ring (21). Remove seal (22) and O-ring seal (23). Remove thrust washers (24).
Note: Note the quantity and the order of thrust washers (24).
Show/hide tableIllustration 11 g01379246 - Remove bearings (25).
Note: If bearings (25) are removed, replace bearings (25).
Show/hide tableIllustration 12 g01379256 - Remove lip seal (26). Repeat this step for the remaining lip seals (26).
Show/hide table
Illustration 13 g01379258 - Remove lip seal (27). Repeat this step for the remaining lip seals (27).
Show/hide table
Illustration 14 g01379263 - Use Tooling (A) and a suitable lifting device in order to remove bearing (28). Repeat this step for the remaining bearing (28).
Show/hide table
Illustration 15 g01379267 - Use Tooling (A) and a suitable lifting device in order to remove bearing (29). Repeat this step for the remaining bearing (29).
Show/hide table
Illustration 1 | g01379099 |
Caterpillar Information System:
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Tip Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Articulation Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Accumulator (Blade Cushion) - Remove and Install
Improved Axles Are Available for Certain Vibratory Utility Compactors {7113} Improved Axles Are Available for Certain Vibratory Utility Compactors {7113}
2015/05/15 Sonic Sensor Kits Are Now Available on AP255E Asphalt Paver for the Conveyor and Auger {1408, 5657}
Procedure to Install Conveyor and Auger Sonic Sensors on AP255E, Paver {1408, 5657} Procedure to Install Conveyor and Auger Sonic Sensors on AP255E, Paver {1408, 5657}
Bench Test Procedure for 420F2, 426F2, 427F2, 428F2, 430F2, 432F2, 434F2, 440, 444F2, and 450 Backhoe Loader Transmissions {3030, 3073, 3139, 5051} Bench Test Procedure for 420F2, 426F2, 427F2, 428F2, 430F2, 432F2, 434F2, 440, 444F2, and 450 Backhoe Loader Transmissions {3030, 3073, 3139, 5051}
CW34 Pneumatic Compactor Cooling System Water Temperature Regulator - Replace
CW34 Pneumatic Compactor Cooling System Water Temperature Regulator - Replace
CW34 Pneumatic Compactor Cooling System Coolant Sample (Level 1) - Obtain
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Arm - Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Bottom Guard - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Brake Accumulator - Remove and Install
2015/04/30 An Improved Air Pressure Gauge For The Brakes Is Now Used On Certain K And K Series 2 Motor Graders {7450, 7451}
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Cab - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Cylinder - Remove and Install
CW34 Pneumatic Compactor Fuel System Primary Filter (Water Separator) - Replace
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Remove and Install
CW34 Pneumatic Compactor Fuel System Secondary Filter - Replace
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Disassemble
Procedure to Update the Steering Accumulator Mounting Bracket System on the 793F CMD Off-Highway Truck {0679, 4331, 5077} Procedure to Update the Steering Accumulator Mounting Bracket System on the 793F CMD Off-Highway Truck {0679, 4331, 5077}
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Assemble