Blade Lift Arm - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
B | 4C-9634 | Puller Stud | 1 |
1P-1836 | Bearing Puller Adapter | 1 | |
1P-1839 | Bearing Puller Adapter | 1 | |
9U-6832 | Nut | 1 | |
6V-3170 | Double Acting Cylinder | 1 | |
3S-6224 | Electric Hydraulic Pump Gp | 1 | |
C | 1P-0510 | Driver Gp | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lower the temperature of bearing (29). Use Tooling (B) and a suitable lifting device in order to install bearing (29). Repeat this step for the remaining bearing (29).
Show/hide table
Illustration 2 g01379361 - Lower the temperature of bearing (29). Use Tooling (B) and a suitable lifting device in order to install bearing (28). Repeat this step for the remaining bearing (28).
Show/hide table
Illustration 3 g01379258 - Use Tooling (C) in order to install lip seal (27). Repeat this step for the remaining lip seals (27).
Show/hide table
Illustration 4 g01379256 - Use Tooling (C) in order to install lip seal (26). Repeat this step for the remaining lip seals (26).
Show/hide table
Illustration 5 g01379246 - Lower the temperature of new bearings (25). Install new bearings (25).
Show/hide table
Illustration 6 g01379242 - Install O-ring seal (23) and seal (22) onto ring (21). Install ring (21) onto yoke (20). Install thrust washers (24). Install yoke (20).
Show/hide table
Illustration 7 g01379234 - Install O-ring seal (16) and seal (17) onto retainer (15). Install thrust washers (19). Install shims (18). Use a number of shims (18) to obtain a maximum end play of
0.250 mm (0.0098 inch) . Install retainer (15). Install bolts (14).Note: The yoke must rotate freely.
Show/hide tableIllustration 8 g01379220 - Use two suitable lifting devices in order to install arm assembly (3). The weight of arm assembly (3) is approximately
182 kg (410 lb) .Show/hide tableIllustration 9 g01379155 - Position thrust washers (13). Install pin (12).
Note: The clearance between the centershift lock bar and the lock plate must be
2.3 ± 0.8 mm (0.09 ± 0.03 inch) .Show/hide tableIllustration 10 g01379147 - Install lock (11) and bolts (10).
Show/hide table
Illustration 11 g01379129 - Position thrust washers (9). Install pin (8).
Note: The clearance between the centershift lock bar and the lock plate must be
2.3 ± 0.8 mm (0.09 ± 0.03 inch) .Show/hide tableIllustration 12 g01379124 - Install plate (7) and bolt (6). Tighten bolt (6) to a torque of
115 ± 10 N·m (85 ± 7 lb ft) .Show/hide tableIllustration 13 g01379116 - Install lock (5) and bolts (4).
Show/hide table
Illustration 14 g01379099 - Use a suitable lifting device in order to position cylinder (1). The weight of cylinder (1) is approximately
91 kg (200 lb) . Install bolts (2).
Show/hide table
Illustration 1 | g01379343 |
Caterpillar Information System:
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Arm - Remove
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Tip Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade Lift Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Blade - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Articulation Cylinder - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Accumulator (Blade Cushion) - Remove and Install
Improved Axles Are Available for Certain Vibratory Utility Compactors {7113} Improved Axles Are Available for Certain Vibratory Utility Compactors {7113}
2015/05/15 Sonic Sensor Kits Are Now Available on AP255E Asphalt Paver for the Conveyor and Auger {1408, 5657}
Procedure to Install Conveyor and Auger Sonic Sensors on AP255E, Paver {1408, 5657} Procedure to Install Conveyor and Auger Sonic Sensors on AP255E, Paver {1408, 5657}
Bench Test Procedure for 420F2, 426F2, 427F2, 428F2, 430F2, 432F2, 434F2, 440, 444F2, and 450 Backhoe Loader Transmissions {3030, 3073, 3139, 5051} Bench Test Procedure for 420F2, 426F2, 427F2, 428F2, 430F2, 432F2, 434F2, 440, 444F2, and 450 Backhoe Loader Transmissions {3030, 3073, 3139, 5051}
CW34 Pneumatic Compactor Cooling System Water Temperature Regulator - Replace
CW34 Pneumatic Compactor Cooling System Water Temperature Regulator - Replace
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Bottom Guard - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Brake Accumulator - Remove and Install
2015/04/30 An Improved Air Pressure Gauge For The Brakes Is Now Used On Certain K And K Series 2 Motor Graders {7450, 7451}
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Cab - Remove and Install
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Cylinder - Remove and Install
CW34 Pneumatic Compactor Fuel System Primary Filter (Water Separator) - Replace
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Remove and Install
CW34 Pneumatic Compactor Fuel System Secondary Filter - Replace
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Disassemble
Procedure to Update the Steering Accumulator Mounting Bracket System on the 793F CMD Off-Highway Truck {0679, 4331, 5077} Procedure to Update the Steering Accumulator Mounting Bracket System on the 793F CMD Off-Highway Truck {0679, 4331, 5077}
16M Series 3 and 18M Series 3 Motor Graders Machine Systems Centershift Lock - Assemble
PL83 and PL87 Pipelayer Systems Location of Components (Undercarriage)