Power Adjuster Motor Group (Sloper) - Remove and Install
Start By:
- Remove the gerotor motor (slope). Refer to Disassembly and Assembly, "Gerotor Motor (Slope) - Remove and Install".
- Attach a suitable lifting device to power adjuster motor group (3). The weight of power adjuster motor group (3) is approximately
35 kg (77 lb) . - Remove bolt (1) and the spacer.
- Remove bolt (2) and the spacer.
Show/hide table
Illustration 2 g03679516 - Remove pin lock (5), pin (4), and power adjuster motor group (3).
Show/hide table
Illustration 3 g03679568 - Loosen nut (7) and remove clevis (6). Remove nut (7).
- Remove the four bolts, the four washers, the four nuts, and plate assembly (8).
- Loosen the set screws. Remove coupler group (9) from actuator group (10).
Show/hide table
Illustration 1 | g03679511 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite 272 | 1 |
B | - | Loctite C5A Cooper Anti-Seize | 1 |
- Install power adjuster motor group (3) in the reverse order of removal.
- Tighten the set screws on coupler group (9) to a torque of
25 ± 6 N·m (221 ± 53 lb in) .Show/hide tableIllustration 4 g03679593 - Install nut (7) to (X)
16.9 ± 1.5 mm (0.7 ± 0.1 inch) . - Install clevis (6) to (Y)
242.5 ± 1.5 mm (9.5 ± 0.1 inch) . - Apply Tooling (A) to nut (7).
- Tighten nut (7) to a torque of
425 ± 42 N·m (313 ± 31 lb ft) . - Apply Tooling (B) to the spacers.
- Tighten the set screws on coupler group (9) to a torque of
End By:
- Install the gerotor motor (slope). Refer to Disassembly and Assembly, "Gerotor Motor (Slope) - Remove and Install".
Caterpillar Information System:
725C Articulated Truck Clean Emissions Module - Remove and Install
SE60 Asphalt Screed Screed Frame (Extender) - Remove and Install
SE60 Asphalt Screed Screed Frame (Main) - Remove and Install
SE60 Asphalt Screed Screed Plate (Main) - Remove and Install
SE50 VT Asphalt Screed Shoe (End Gate) - Remove and Install
SE50 V Asphalt Screed System Pressure - Release
SE60 Asphalt Screed Tamper Bar (Extender Screed) - Remove and Install
794 AC Off-Highway Truck Systems Brake System
SE50 VT Asphalt Screed Vibratory Group - Assemble
SE50 VT Asphalt Screed Vibratory Group - Disassemble
SE60 Asphalt Screed Nose Bar (Main Screed) - Remove and Install
SE60 Asphalt Screed Crown Group - Remove and Install
SE60 Asphalt Screed Power Adjuster Motor Group (Extender Height) - Remove and Install
794 AC Off-Highway Truck Systems Pressure Sensor (Payload Monitor)
794 AC Off-Highway Truck Systems Rear Suspension (Cylinder)
794 AC Off-Highway Truck Systems Front Suspension (Cylinder)
Cat® Terrain for Track-Type Tractor with Blade Control Display Module
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Power Train Torque Converter to Transmission, Output Transfer Gears - Connect
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Steering Pilot System
16M Series 3 and 18M Series 3 Motor Grader Hydraulic Fan Speed - Test
16M Series 3 and 18M Series 3 Motor Grader Oil Cooler (Hydraulic Fan)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Power Train Transmission from Output Transfer Gears - Separate
2014/05/09 New Software Patch Available for MineStar Fleet Office v3.1.1 {7605}
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Monitoring System (Brake Functions)