Engine Overspeeds
Use this procedure in order to troubleshoot an engine overspeed or use this procedure if the following event code is active. Refer to Troubleshooting, "Event Codes" for information about event codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".
Note: Some of the following codes may not be applicable for certain applications.
Show/hide table
Diagnostic Trouble Codes | |||
---|---|---|---|
CDL Code | J1939 Code | Code Description
(code descriptions may vary) |
Comments |
E362 (1) | 190-15 | Engine Overspeed | The code is logged. |
E362 (3) | 190-0 | Engine Overspeed | The code requires factory passwords to be cleared. |
- Proceeding down steep grades (if applicable)
- Proper operation of the turbocharger
- Intake air
- Starting aids that are not operating properly
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Proceeding Down Steep Grades (If Applicable) Engaging the engine brakes on a steep grade may be necessary. A. The operator needs to understand the proper operation of the machine while using the engine brakes. Not all applications have engine brakes. |
Steep grades |
Result: Steep grades are the cause of the overspeed. Repair: Control the engine speed during steep grades. Result: Steep grades are not the cause of the overspeed. Proceed to Test Step 2. |
2. Proper Operation of the Turbocharger A. Check for proper operation of the turbocharger. B. Check for any oil that may be leaking into the air inlet. |
Turbocharger |
Result: The turbocharger is leaking oil into the inlet. Repair: Repair or replace the turbocharger. Result: The turbocharger is not leaking oil into the inlet. Proceed to Test Step 3. |
3. Intake Air A. Check for combustible gases in the surrounding atmosphere. B. Check for proper operation of starting aids (if equipped). |
Air quality |
Result: The atmosphere has combustible gases. Repair: Do not operate the engine in an environment with combustible gases. |
Caterpillar Information System:
14L Motor Grader Solenoid Valve (ARD Fuel) - Remove and Install - Main
966M and 972M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Power Train System)
994K Wheel Loader Commissioning Procedure {0374, 1000, 7000, 7960, 7961} 994K Wheel Loader Commissioning Procedure {0374, 1000, 7000, 7960, 7961}
2013/11/04 New Ferrite Bead and Relay Harness Is Now Available For Certain Generator Sets Equipped With PL421 {4450, 7606}
Cat® Terrain v5 for Grading and Loading Truck Load Windows
14L Motor Grader Pressure Sensor (DPF) - Remove and Install
14L Motor Grader Clean Emissions Module - Remove and Install
2013/10/25 Machine Engine ECM Clearing Process for Dealers Is Now Available on Certain Applications {1901, 1920}
966M and 972M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Brake System)
Comfort Series Seat For Caterpillar Machines Troubleshooting
777G Off-Highway Truck Hydraulic and Braking System Parking and Secondary Brake Release System Leakage - Check
Comfort Series Seat For Caterpillar Machines Component Descriptions
C7 and C9 Industrial Engines Exhaust Has Excessive Black Smoke
14L Motor Grader Solenoid Valve (ARD Fuel) - Remove and Install - Pilot
988K Wheel Loader, 834K Wheel Dozer and 836K Compactor Machine Systems Steering Neutralizer Valve - Remove and Install
Installation of the 351-8997 Air Lines Gp for Certain 797F Off-Highway Truck Engines{1071} Installation of the 351-8997 Air Lines Gp for Certain 797F Off-Highway Truck Engines{1071}
14L Motor Grader Temperature Sensor (Catalyst Inlet) - Remove and Install
770G and 772G Off-Highway Truck Systems Control Manifold (Steering) - Test and Adjust
770G and 772G Off-Highway Truck Systems Piston Pump (Steering) Pressure - Test and Adjust
2014/01/14 A New Torsional Coupling Assembly and Flywheel Is Now Used on Certain 14M and 16M Motor Graders {3252, 3279}
C7 and C9 Industrial Engines Power Is Intermittently Low or Power Cutout Is Intermittent
994K Wheel Loader Stairway (Powered) Operation - If Equipped
2013/11/21 New Ether Aid Line Components Are Used On Certain C175 Off-Highway Truck Engines {1456}
770G and 772G Off-Highway Truck Systems Rear Suspension (Cylinder) - Purge and Charge