Solenoid Valve (ARD Fuel) - Remove and Install - Main
Show/hide table
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. Turn the disconnect switch OFF when draining and/or removing any fuel system components. |
- Remove panel (1).
Show/hide table
Illustration 2 g03499241 - Cut cable straps (4). Disconnect harness assembly (3). Remove solenoid valve assembly (2).
Show/hide table
Illustration 3 g03515167 Note: Cleanliness is an important factor. Before the disassembly procedure, clean the exterior of the component thoroughly. This action will help to prevent dirt from entering the internal mechanism.
- Remove nut (9), washer (8), and solenoid (7) from valve assembly (2).
- Remove cartridge assembly (6) and remove O-ring seals (5).
Show/hide table
Illustration 1 | g03504345 |
- Install solenoid valve (2) in the reverse order of removal.
- Tighten cartridge assembly (6) to a torque of
50 ± 5 N·m (37 ± 4 lb ft) . - Tighten nut (9) to a torque of
20 ± 2.5 N·m (177 ± 22 lb in) .
- Tighten cartridge assembly (6) to a torque of
Caterpillar Information System:
966M and 972M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Power Train System)
994K Wheel Loader Commissioning Procedure {0374, 1000, 7000, 7960, 7961} 994K Wheel Loader Commissioning Procedure {0374, 1000, 7000, 7960, 7961}
2013/11/04 New Ferrite Bead and Relay Harness Is Now Available For Certain Generator Sets Equipped With PL421 {4450, 7606}
Cat® Terrain v5 for Grading and Loading Truck Load Windows
14L Motor Grader Pressure Sensor (DPF) - Remove and Install
14L Motor Grader Clean Emissions Module - Remove and Install
2013/10/25 Machine Engine ECM Clearing Process for Dealers Is Now Available on Certain Applications {1901, 1920}
966M and 972M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Brake System)
Comfort Series Seat For Caterpillar Machines Troubleshooting
777G Off-Highway Truck Hydraulic and Braking System Parking and Secondary Brake Release System Leakage - Check
Comfort Series Seat For Caterpillar Machines Component Descriptions
Reusability of Worm Gear Sets {5207, 7552} Reusability of Worm Gear Sets {5207, 7552}
C27 and C32 Engines for Caterpillar Built Machines Engine Overspeeds
C7 and C9 Industrial Engines Exhaust Has Excessive Black Smoke
14L Motor Grader Solenoid Valve (ARD Fuel) - Remove and Install - Pilot
988K Wheel Loader, 834K Wheel Dozer and 836K Compactor Machine Systems Steering Neutralizer Valve - Remove and Install
Installation of the 351-8997 Air Lines Gp for Certain 797F Off-Highway Truck Engines{1071} Installation of the 351-8997 Air Lines Gp for Certain 797F Off-Highway Truck Engines{1071}
14L Motor Grader Temperature Sensor (Catalyst Inlet) - Remove and Install
770G and 772G Off-Highway Truck Systems Control Manifold (Steering) - Test and Adjust
770G and 772G Off-Highway Truck Systems Piston Pump (Steering) Pressure - Test and Adjust
2014/01/14 A New Torsional Coupling Assembly and Flywheel Is Now Used on Certain 14M and 16M Motor Graders {3252, 3279}
C7 and C9 Industrial Engines Power Is Intermittently Low or Power Cutout Is Intermittent
994K Wheel Loader Stairway (Powered) Operation - If Equipped
2013/11/21 New Ether Aid Line Components Are Used On Certain C175 Off-Highway Truck Engines {1456}