Idler Gears (Front) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0520     | 冲头总成     | 1     |
开始:
- 拆卸发动机机油和水泵驱动器。 参考拆解与组装, "发动机机油和水泵驱动器 - 拆卸"。
- 拆卸燃油和辅助水泵驱动器。 参考拆解与组装, "燃油和辅助水泵驱动器 - 拆卸"。
- 拆卸减振器。 参考拆解和组装, "减振器 - 拆卸和安装"。
- 拆下螺栓 (1 ) 。 拆下罩盖 (2) 。 拆下螺栓 (3 ) 。 拆下盖 (4) 。 卸下螺栓 (5) 。 拆下螺栓 (6) 。 拆下前壳体背面和各惰轮轴后部上的两个惰轮螺栓。
Show/hide table
图 1 | g01596074 |
- 支撑住惰轮 (7) 。 拆下销 (8) 。 拆下惰轮轴。 将惰轮 (7) 降到前驱动壳体底部。 从前驱动壳体背面拆卸惰轮 (7) 。
Show/hide table
图 2 | g01596077 |
Show/hide table
图 3 | g01229252 |
- 使用工具 (A) 和适当的压具,将轴承 (9) 从齿轮 (7) 上拆下。
Show/hide table
图 4 | g01229253 |
- 对于另一侧,重复步骤2 至3。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0520     | 冲头总成     | 1     |
- 使用工具 (A) 和适当的压具将轴承 (9) 安装到齿轮 (7) 中。
Show/hide table
图 5 | g01229253 |
- 将惰轮 (7) 安置在前驱动壳体背面。 将惰轮 (7) 从前驱动壳体底部提升到位。 安装惰轮轴。 将销 (8) 装入惰轮 (7) 中。
Show/hide table
图 6 | g01229252 |
Show/hide table
图 7 | g01596077 |
- 对于另一侧,重复步骤1 至2。
- 安装前壳体背面和各轴后部上的两个惰轮螺栓。 安装螺栓 (6) 。 安装螺栓 (5) 。 安装盖 (4) 。 安装螺栓 (3) 。 安装罩盖 (2) 。 安装螺栓 (1) 。
Show/hide table
图 8 | g01596074 |
End By:
- 安装减振器。 参考 拆解和组装, "减振器 - 拆卸和安装"。
- 安装燃油和辅助水泵驱动器。 参考 拆解与组装, "燃油和辅助水泵驱动器 - 安装"。
- 安装发动机机油和水泵驱动器。 参考 拆解与组装, "发动机机油和水泵驱动器 - 安装"。
Caterpillar Information System:
422E and 428E Backhoe Loaders Before Roading the Machine
3512C Engine and 785D Off-Highway Truck/Tractors Component Location
3512C Engine and 785D Off-Highway Truck/Tractors System Overview
785D OEM Off-Highway Truck Machine Systems Check Valve (Rear Air/Hydraulic Cylinder) - Remove and Install
785D OEM Off-Highway Truck Machine Systems Check Valve (Front Air/Hydraulic Cylinder) - Remove and Install
785D OEM Off-Highway Truck Machine Systems Brake Tank (Makeup) - Remove and Install
MINEGEM Machine Control ; Guidance Products Circuit Breakers - Reset - R1300G LJB
R1300G Load Haul Dump Braking System Pressure Sensor (Transmission Oil)
793F Off-Highway Truck Rollover Protective Structure (ROPS) - Inspect
1390 Track Feller Buncher Operational Checks
PL61 Pipelayer Machine Systems Winch - Assemble - Boom
785D OEM Off-Highway Truck Machine Systems Slack Adjuster - Assemble
2008/07/07 Improved Links Are Available For Certain Thumbs {6513, 6547}
2008/08/25 Improved K110 Adapters are now available for Wheel Loaders and Excavators {6800}
1090 Series II, 1190 Series II, 1190T Series II and 1290T Series II Track Feller Bunchers Machine Systems Swing Motor Relief Valve Pressure - Test and Adjust
Remote Forward, Neutral, and Reverse Switch May Not Operate Correctly{3065, 7332} Remote Forward, Neutral, and Reverse Switch May Not Operate Correctly{3065, 7332}
AP600D Asphalt Paver Machine Systems General Information (Generator System)
AP600D Asphalt Paver Machine Systems Hydraulic Schematic (Generator System)
2008/07/21 Improvements Have Been Made to the Caterpillar Monitoring System {7450, 7451, 7490}
AP600D Asphalt Paver Machine Systems Operator Controls (Generator)
320D and 323D Excavators Machine System Specifications Accumulator (Pilot)
PL61 Pipelayer Machine Systems Hook Winch - Disassemble
2009/03/30 The Installation of the Shim Pack is Updated for the Front Wheel Bearing {3259, 4201, 4205}
AP600D Asphalt Paver Machine Systems Electrical Schematic (Generator System)