Control Manifold and Solenoid (Parking Brake) - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
ZZ | 6V-9508 | 端面密封螺塞 (11/16 - 16 螺纹) | 3 |
6V-9829 | 盖组件 (11/16 - 16 螺纹) | 3 | |
6V-9509 | 端面密封螺塞 (13/16 - 16 螺纹) | 2 | |
6V-9830 | 盖组件 (13/16 - 16 螺纹) | 2 |
开始:
- 释放液压系统压力。 请参阅拆解和组装, "液压系统压力 - 释放"。
- 倾斜驾驶室。 请参阅拆解和组装, "驾驶室 - 倾斜"。
注: 维修数据:拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
注: 在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记,以便安装。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏,并有助于防止污染物进入系统。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。 污染物或污垢可能会损坏精密部件。 拆解步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
- 断开线束组件 (4)。 断开软管组件 (1) 和 (6)。
- 断开软管组件 (7)。 断开管组件 (3)。 拆下螺栓 (2 )。 拆下歧管 (5)。
Show/hide table
图 2 g01053721 注: 观察接头的方向。
- 拆下电磁阀 (7)。 拆下接头 (8)、 (9) 和 (10)。
Show/hide table
图 1 | g01053710 |
- 安装电磁阀 (7)。 在接头中安装新的 O 形密封圈。 安装接头 (10)、 (9) 和 (8)。
Show/hide table
图 4 g01053710 - 把歧管装上。 安装螺栓 (2)。 将螺栓拧紧至
20 ± 5 N·m (15 ± 4 lb ft) 。 连接管组件 (3)。 连接软管组件 (6)。 - 连接软管组件 (5) 和 (1)。 连接线束组件 (4)。
- 检查液压油油位。 请参阅操作和保养手册, "液压油油位 - 检查"。
Show/hide table
图 3 | g01053721 |
注: 观察接头的方向。
结束:
- 降下驾驶室。 请参阅拆解和组装, "驾驶室 - 倾斜"。
Caterpillar Information System:
587R Pipelayer Machine Systems Boom Winch Motor - Install
587R Pipelayer Machine Systems Boom Winch Motor - Remove
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Main Control Valve
587R Pipelayer Machine Systems Accumulator - Remove and Install
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Install
2007/07/09 Acceptable Gap Between Lift Arm and Stop Block on Skid Steer Loaders and Multi Terrain Loaders {6119, 7050}
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Assemble
3412E Engine for Caterpillar Built Machines Cat Data Link - Test
24M Motor Grader Power Train Electronic Control System Using Messenger to Determine Diagnostic Codes
C6.6 Engines for Caterpillar Built Machines Air Compressor - Remove and Install
C6.6 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C6.6 Engines for Caterpillar Built Machines Alternator - Install - Alternators with Mounting Lugs
AP655D and BG655D Asphalt Pavers Machine Systems Hydraulic Schematic (Auxiliary Hydraulic System) - Steel Track Machine
3412E Engine for Caterpillar Built Machines Pressure Sensor - Calibrate
C15 and C18 Generator Set Engines Radiator Core - Remove and Install - Charge Air
AP655D and BG655D Asphalt Pavers Propel System General Information (Propel System) - Steel Track Machine
2007/07/30 Gasket for the Valve Mechanism Cover {1107, 1120, 7555}
3412E Engine for Caterpillar Built Machines Timing - Calibrate
AP655D and BG655D Asphalt Pavers Propel System Location of Hydraulic Components (Propel System) - Steel Track Machine
24M Motor Grader Power Train Transmission Lubrication
AP655D and BG655D Asphalt Pavers Propel System Piston Pump (Propel) - Steel Track Machine
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install - Electric Fuel Priming Pump
2007/07/09 New Installation Sleeves for the Transmission Clutches Are Now Available {0720, 3030, 3155}
2010/09/13 Improvements to the Lower Transmission Mount {3082}