Track Drive - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 169-6969 | 公制螺柱 | 2 |
- 将工具 (A) 安装到活塞马达上,彼此相隔 180°。
- 将适当的起吊设备连接到履带驱动装置 (2)。 履带驱动装置 (2) 的重量约为
29 kg (64 lb) 。 使用适当的起吊设备将履带驱动装置 (2) 定位到工具 (A) 上。 - 从履带驱动装置 (2) 上拆下适当的起吊设备,并将适当的起吊设备连接到履带 (1) 上。 履带 (1) 的重量约为
86 kg (190 lb) 。 提升履带 (1) 以清洁履带驱动装置 (2)。 - 在工具 (A) 上将履带驱动装置 (2) 滑动就位。
Show/hide table
图 2 g01336897 典型示例 - 将螺栓 (3) 安装到履带驱动装置 (2) 上。 此时请勿拧紧螺栓 (3)。
- 从履带驱动装置 (2) 中拆下工具 (A),然后将其余两个螺栓 (3) 安装到履带驱动装置 (2)。
- 以交叉模式将螺栓 (3) 拧紧至扭矩为
270 ± 40 N·m (200 ± 30 lb ft) 。 - 拆下适当的起吊设备并调整履带张力。 请参阅操作和保养手册, "履带(橡胶)- 检查/调整"。
Show/hide table
图 1 | g01336975 |
典型示例 |
Caterpillar Information System:
2007/07/09 Acceptable Gap Between Lift Arm and Stop Block on Skid Steer Loaders and Multi Terrain Loaders {6119, 7050}
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Assemble
3412E Engine for Caterpillar Built Machines Cat Data Link - Test
24M Motor Grader Power Train Electronic Control System Using Messenger to Determine Diagnostic Codes
C6.6 Engines for Caterpillar Built Machines Air Compressor - Remove and Install
C6.6 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C6.6 Engines for Caterpillar Built Machines Alternator - Install - Alternators with Mounting Lugs
C6.6 Engines for Caterpillar Built Machines Alternator - Install - Alternators with Mounting Pads
C6.6 Engines for Caterpillar Built Machines Alternator - Remove - Alternators with Mounting Lugs
C6.6 Engines for Caterpillar Built Machines Alternator - Remove - Alternators with Mounting Pads
C6.6 Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
C6.6 Engines for Caterpillar Built Machines ECM Mounting Bracket - Remove and Install
587R Pipelayer Machine Systems Accumulator - Remove and Install
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Main Control Valve
587R Pipelayer Machine Systems Boom Winch Motor - Remove
587R Pipelayer Machine Systems Boom Winch Motor - Install
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Control Manifold and Solenoid (Parking Brake) - Remove and Install
AP655D and BG655D Asphalt Pavers Machine Systems Hydraulic Schematic (Auxiliary Hydraulic System) - Steel Track Machine
3412E Engine for Caterpillar Built Machines Pressure Sensor - Calibrate
C15 and C18 Generator Set Engines Radiator Core - Remove and Install - Charge Air
AP655D and BG655D Asphalt Pavers Propel System General Information (Propel System) - Steel Track Machine
2007/07/30 Gasket for the Valve Mechanism Cover {1107, 1120, 7555}
3412E Engine for Caterpillar Built Machines Timing - Calibrate
AP655D and BG655D Asphalt Pavers Propel System Location of Hydraulic Components (Propel System) - Steel Track Machine