Rear Axle, Differential and Final Drive - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7576     | 连杆支架     | 4     |
B     | 1U-9200     | 操纵杆滚轮起重机     | 1     |
C     | 1U-7505     | 液压千斤顶     | 1     |
D     | 138-7575     | 连杆支架     | 4     |
E     | 6V-6146     | 均载梁     | 1     |
F     | 1U-9744     | 地面千斤顶     | 1     |
G     | 155-0695     | 螺纹锁固胶     | 1     |
- 安装支架组件 (22) 。
Show/hide table
图 1 | g01389836 |
- 使用工具 (D) 、工具 (E) 、工具 (F) 和两个适当的起吊装置定位后轴、差速器和终传动 (17) 。 后轴、差速器和终传动 (17) 的重量约为 1828 kg (4030 lb)。
Show/hide table
图 2 | g01389824 |
Show/hide table
图 3 | g01389825 |
- 将工具 (G) 涂敷到螺栓 (19) 上。 安置支架组件 (20) 并安装螺栓 (19) 。 对机器的另一侧重复此步骤。
Show/hide table
图 4 | g01389829 |
- 将工具 (G) 涂抹到螺栓 (18) 上。 安装螺栓 (18) 。 对机器的另一侧重复此步骤。
Show/hide table
图 5 | g01389828 |
- 根据所示的顺序拧紧螺栓 (21) 和螺栓 (18) 至200 N·m (148 lb ft) 的扭矩。 再次拧紧螺栓 (21) 和螺栓 (18) 至 900 ± 100 N·m (664 ± 74 lb ft) 的扭矩。
Show/hide table
图 6 | g01389840 |
- 安装面板 (16) 。 对发动机外壳的另一侧重复此步骤。
Show/hide table
图 7 | g01389823 |
- 连接软管组件 (15) 。
Show/hide table
图 8 | g01389822 |
- 安装锁定阀 (14) 。 连接软管组件 (13) 。 安装管组件 (12) 。 连接软管 (11) 。
Show/hide table
图 9 | g01389821 |
- 安装管组件 (10) 。 安装软管 (9) 。 连接软管组件 (8) 。 安装管组件 (7) 。 安装线束组件 (6) 。 安装管组件 (5) 。
Show/hide table
图 10 | g01389813 |
- 使用工具 (C) 提高连杆 (1) 。 连杆 (1) 的重量约为 75 kg (165 lb)。 安装销 (4) 。 安装螺栓 (3) 和螺母 (2) 。 对其余连杆重复此步骤。
Show/hide table
图 11 | g01389812 |
- 对机器另一侧,重复步骤 1 至步骤 10。
- 安装后桥。 请参阅操作和保养手册, "变速箱和差速器用油 - 更换"。
- 分离转向机架锁。 请参阅操作和保养手册, "转向机架锁"。
End By:
- 安装底部防护罩。 请参阅 拆解和组装, "底部防护罩 - 拆卸和安装"。
- 安装纵列传动箱壳体。 请参阅 拆解和组装, "壳体(纵列) - 拆卸和安装"。
- 安装后轮和轮胎。 请参阅 拆解和装配, "车轮和轮胎(后)- 拆卸和安装"。
- 安装传动链。 请参阅 拆解和组装, "传动链条 - 安装"。
Caterpillar Information System:
16M Motor Grader Power Train Rear Axle, Differential and Final Drive - Remove
2007/07/09 New Software is Now Available {1901, 1902, 7620}
C4.4 and C6.6 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
16M Motor Grader Power Train Housing (Tandem) - Remove and Install
AP655D and BG655D Asphalt Pavers Machine Systems Steering Column - Assemble
AP655D and BG655D Asphalt Pavers Machine Systems Steering Column - Disassemble
16M Motor Grader Power Train Service Brake (Wheel Spindle) - Install
16M Motor Grader Power Train Service Brake (Wheel Spindle) - Remove
AP655D Asphalt Paver Machine Systems Hydraulic Tank - Remove and Install
C4.4 and C6.6 Engines for Caterpillar Built Machines Glossary
C4.4 and C6.6 Engines for Caterpillar Built Machines System Overview
2007/07/23 Improved Power Train Software Now Used {7610, 7620}
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Wiring Information
AS3251C Asphalt Screed Electronic Control Module (Screed)
Procedure to Install Forward/Neutral/Reverse (FNR) Switch{5702, 7332} Procedure to Install Forward/Neutral/Reverse (FNR) Switch{5702, 7332}
AS3251C Asphalt Screed Operator Controls
2007/06/25 Correction to Operation and Maintenance Manual , "Hoist System and Brake System Oil Level - Check" {5056}
16M Motor Grader Power Train Transmission Oil Filter Base - Remove
16M Motor Grader Power Train Transmission Oil Filter Base - Install
AS3251C Asphalt Screed Screed Components
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Priority Valve - Inlet Manifold of the Loader
24M Motor Grader Power Train Electronic Control System MID 027 - CID 1639 - FMI 09
2007/07/16 Improved Walkways are Available {7255}
16M Motor Grader Power Train Transmission Oil Cooler - Remove