Transmission Oil Cooler - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
注: 检查 O 形密封圈。 更换磨损或损坏的 O 形密封环。
- 将液压油排入适当的容器以便保存或处理。 请参阅操作和保养手册, "液压系统机油 – 更换"。
- 将发动机冷却液排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 拆下面板 (1) 。
Show/hide table
图 1 | g01390102 |
- 断开软管 (2) 。
Show/hide table
图 2 | g01390103 |
- 拆下卡箍 (3) 。
Show/hide table
图 3 | g01390106 |
- 断开弯头 (4) 。 拆下管 (5) 。
Show/hide table
图 4 | g01390107 |
- 断开软管组件 (6) 。 断开管组件 (7) 。 断开软管组件 (8) 。
Show/hide table
图 5 | g01390112 |
- 拆下弯头 (9) 。
Show/hide table
图 6 | g01390120 |
- 卸下支架 (10) 。
Show/hide table
图 7 | g01390185 |
- 拆下支架 (11) 。
Show/hide table
图 8 | g01390188 |
- 将工具 (A) 和适当的起吊设备固定到变速油冷却器 (12) 上。 变速箱油冷却器 (12) 的重量约为 30 kg (66 lb)。 拆下螺栓 (13) 和螺栓 (14) 。 拆下变速箱油冷却器 (12) 。
Show/hide table
图 9 | g01390197 |
Show/hide table
图 10 | g01390200 |
- 拆下联轴器 (15) 。 拆下 O 形密封圈 (16) 。
Show/hide table
图 11 | g01390202 |
- 拆下 O 形密封圈 (17) 。
Show/hide table
图 12 | g01390204 |
Caterpillar Information System:
2007/07/16 Improved Walkways are Available {7255}
24M Motor Grader Power Train Electronic Control System MID 027 - CID 1639 - FMI 09
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Priority Valve - Inlet Manifold of the Loader
AS3251C Asphalt Screed Screed Components
16M Motor Grader Power Train Transmission Oil Filter Base - Install
16M Motor Grader Power Train Transmission Oil Filter Base - Remove
2007/06/25 Correction to Operation and Maintenance Manual , "Hoist System and Brake System Oil Level - Check" {5056}
AS3251C Asphalt Screed Operator Controls
Procedure to Install Forward/Neutral/Reverse (FNR) Switch{5702, 7332} Procedure to Install Forward/Neutral/Reverse (FNR) Switch{5702, 7332}
AS3251C Asphalt Screed Electronic Control Module (Screed)
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Wiring Information
16M Motor Grader Power Train Rear Axle, Differential and Final Drive - Install
16M Motor Grader Power Train Transmission Oil Cooler - Install
C15 and C18 Generator Set Engines Fan Guard - Remove and Install
587R Pipelayer Power Train Transmission and Bevel Gears - Remove
587R Pipelayer Power Train Transmission and Bevel Gears - Install
AS4251C Asphalt Paver Specifications
C15 and C18 Generator Set Engines Fan - Remove and Install
AS3251C Asphalt Screed Screed Control System
24M Motor Grader Hydraulic and Steering System Control Manifold (Implement, Steering)
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Valve (Lift)
AP655D and BG655D Asphalt Pavers Propel System Piston Pump Flow - Test - Steel Track
AS4251C Asphalt Paver Plate Locations and Film Locations
EquipmentManager Dealer Administrator Manual Setup Subscriptions