Engine Enclosure (Hood) - Remove
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Loosen hose clamp (2) in order to disconnect hose (3) from ejector (1). Loosen clamp (4) and remove ejector assembly (1) .
Show/hide table
 | |
| Illustration 1 | g01372987 |
- Disconnect hose (5). Loosen clamp (6) and disconnect elbow (7). Disconnect hose (8) .
Show/hide table
 | |
| Illustration 2 | g01372754 |
- Remove bolts (9). Disconnect clip (10) and remove hose (11) .
Show/hide table
 | |
| Illustration 3 | g01372774 |
- Reposition harness assemblies (12) .
Show/hide table
 | |
| Illustration 4 | g01372778 |
- Disconnect harness assembly (13) and harness assembly (14) .
Show/hide table
 | |
| Illustration 5 | g01372804 |
- Remove bolts (15) and reposition plate (16).
Show/hide table
 | |
| Illustration 6 | g01372782 |
Show/hide table
 | |
| Illustration 7 | g01372784 |
- Remove grommet (17) in order to remove harness assembly (14) from plate (16) .
- Loosen clamp (19) and remove precleaner assembly (18) .
Show/hide table
 | |
| Illustration 8 | g01372819 |
- Disconnect harness assembly (20) and harness assembly (22) .
Show/hide table
 | |
| Illustration 9 | g01372827 |
- Remove bolts (21) in order to reposition the circuit breaker panel.
- Remove bolts (23). Repeat on the opposite side.
- Attach a suitable lifting device to engine enclosure (24). The weight of engine enclosure (24) is approximately 408 kg (900 lb). Disconnect ground shut off switch (26) .
Show/hide table
 | |
| Illustration 10 | g01372883 |
Show/hide table
 | |
| Illustration 11 | g01372877 |
- Remove bolts (25). Repeat on the opposite side.
- Use the suitable lifting device in order to remove engine enclosure (24) .
Caterpillar Information System:
2007/04/30 An Improved Starting Motor is Now Available {1453}
AccuGrade® GPS (CD700) Level Surface Design
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Breaker Relief Valve
2007/06/04 Improvements to the Water Lines Groups {1380}
AccuGrade® GPS (CD700) Designs
CP54 and CS54 Vibratory Soil Compactors Machine Systems Propel Cable - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Machine Systems Cab - Install
AS3251C Asphalt Screed Gear Motor (Vibratory)
3500C Marine Engines Engine Speed/Timing Sensor
AP655D and BG655D Asphalt Pavers Paver Blade - If equipped
AccuGrade® GPS (CD700) Horizontal Guidance
CP54 and CS54 Vibratory Soil Compactors Machine Systems Cab - Remove
160M Motor Grader Engine Supplement Engine Enclosure (Hood) - Install
AccuGrade® GPS (CD700) Sloping Surface Design
AP655D Asphalt Paver Engine Starting
587R Pipelayer Power Train Final Drive, Steering Clutch and Brake - Remove
The Hydraulic Float Function For the Three-Point Hitch is Causing Poor Actuation.{5051, 5702, 5705} The Hydraulic Float Function For the Three-Point Hitch is Causing Poor Actuation.{5051, 5702, 5705}
AccuGrade® GPS (CD700) Configuration
AP655D and BG655D Asphalt Pavers Tracks - Inspect
587R Pipelayer Power Train Final Drive, Steering Clutch and Brake - Install
450E Backhoe Loader Engine Supplement Hydraulic Oil Cooler - Remove and Install
16M Motor Grader Engine Supplement Rear Chassis Support - Remove
16M Motor Grader Engine Supplement Rear Chassis Support - Install
2007/05/14 A New Breaker for the Heating and Air Conditioning System Is Now Used {1417}