Final Drive, Steering Clutch and Brake - Remove
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 8T-3207 | C Frame Assembly | 1 |
| 6V-8199 | Bolt | 2 | |
| 2J-3506 | Nut | 2 | |
| 5P-8248 | Washer | 4 | |
Start By:
- Remove the drive axles. Refer to Disassembly and Assembly, "Drive Axle - Remove".
- Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the final drive and transmission oil into a suitable container for proper storage or disposal. Refer to Operation and Maintenance Manual , "Final Drive and Transmission Oil - Change".
- Move the counterweight to the lowest position for the right side.
Show/hide table
Illustration 1 g01372205 - Remove bolts (1).
Show/hide table
Illustration 2 g01372212 - Adjust Tooling (A), as shown.
Show/hide table
Illustration 3 g01372206 Show/hide table
Illustration 4 g01372209 - Remove the ladder for the left side. Refer to Disassembly and Assembly, "Ladder - Remove".
- Install Tooling (A) and a suitable lifting device to final drive assembly (2). The weight of final drive assembly (2) is approximately
953 kg (2100 lb) . Position Tooling (A), as shown. Remove bolts (3) and bolts (4). Remove final drive assembly (2).Note: DO NOT LOOSEN BOLT (5).
Show/hide table
Illustration 5 g01372215 - Remove O-ring seals (6) and O-ring seal (7).
Caterpillar Information System:
AP655D Asphalt Paver Engine Starting
AccuGrade® GPS (CD700) Sloping Surface Design
160M Motor Grader Engine Supplement Engine Enclosure (Hood) - Install
160M Motor Grader Engine Supplement Engine Enclosure (Hood) - Remove
2007/04/30 An Improved Starting Motor is Now Available {1453}
AccuGrade® GPS (CD700) Level Surface Design
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Breaker Relief Valve
2007/06/04 Improvements to the Water Lines Groups {1380}
AccuGrade® GPS (CD700) Designs
CP54 and CS54 Vibratory Soil Compactors Machine Systems Propel Cable - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Machine Systems Cab - Install
AS3251C Asphalt Screed Gear Motor (Vibratory)
The Hydraulic Float Function For the Three-Point Hitch is Causing Poor Actuation.{5051, 5702, 5705} The Hydraulic Float Function For the Three-Point Hitch is Causing Poor Actuation.{5051, 5702, 5705}
AccuGrade® GPS (CD700) Configuration
AP655D and BG655D Asphalt Pavers Tracks - Inspect
587R Pipelayer Power Train Final Drive, Steering Clutch and Brake - Install
450E Backhoe Loader Engine Supplement Hydraulic Oil Cooler - Remove and Install
16M Motor Grader Engine Supplement Rear Chassis Support - Remove
16M Motor Grader Engine Supplement Rear Chassis Support - Install
2007/05/14 A New Breaker for the Heating and Air Conditioning System Is Now Used {1417}
450E Backhoe Loader Engine Supplement Fuel Cooler - Remove and Install
450E Backhoe Loader Engine Supplement Radiator - Remove and Install
2007/08/20 A New Pin in the Bottom of the Swing frame Can Improve Reliability on Certain Backhoe Loaders {6506}
2007/05/28 The Dimensions for Machining the Internal Spline on the Rear Brake Anchors Have Changed {4251, 4267}