Cab - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 4 |
- Use Tooling (A) and a suitable lifting device to position cab (14) on the machine. The weight of the cab is approximately 850 kg (1874 lb).
Show/hide table
 | |
| Illustration 1 | g01021471 |
- Install bolt (16) that fastens cab tilt cylinder (17) to the bottom of the cab.
Show/hide table
 | |
| Illustration 2 | g00991552 |
- Install pin (15) on both sides of the cab.
Show/hide table
 | |
| Illustration 3 | g00991550 |
- Rotate the valve on cab tilt pump (13) to the RAISE position.
Show/hide table
 | |
| Illustration 4 | g01372628 |
- Insert the pump handle into cab tilt pump (13). Move the handle upward and move the handle downward in order to raise the cab.
- Install pin (12) on both sides of the cab.
Show/hide table
 | |
| Illustration 5 | g00991546 |
- Connect harness assembly (10) and harness assembly (11) .
Show/hide table
 | |
| Illustration 6 | g01372626 |
- Position cable assembly (7) on the propel pump and install pin (8) and the cotter pin. Tighten nut (9) .
Show/hide table
 | |
| Illustration 7 | g01021465 |
- Connect hose assemblies (5) to metering pump (6) .
Show/hide table
 | |
| Illustration 8 | g01021463 |
- Connect hose assemblies (2) .
Show/hide table
 | |
| Illustration 9 | g01372623 |
- Install hoses (3) and tighten the hose clamps.
- Install clamps (4) that fasten hose assemblies (2) and hoses (3) to the bottom of the cab.
- Lower the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
- Open two valves (1) .
Show/hide table
 | |
| Illustration 10 | g01372621 |
- Evacuate the air conditioner system. Charge the air conditioner system. The correct charge is 1.3 kg (2.9 lb). Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
Note: After the cab has been installed, fill the cooling system with coolant to the correct level. Refer to Operation and Maintenance Manual for the correct procedure.
Note: After the cab has been installed, check the hydraulic oil level. Refer to Operation and Maintenance Manual for the correct procedure.
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
AS3251C Asphalt Screed Gear Motor (Vibratory)
3500C Marine Engines Engine Speed/Timing Sensor
AP655D and BG655D Asphalt Pavers Paver Blade - If equipped
AccuGrade® GPS (CD700) Horizontal Guidance
CP54 and CS54 Vibratory Soil Compactors Machine Systems Cab - Remove
Salvage Procedure for the Hydraulic Ejector Cylinder on some Articulated Trucks {5305} Salvage Procedure for the Hydraulic Ejector Cylinder on some Articulated Trucks {5305}
RM-500 Soil Stabilizer Sound Information and Vibration Information
2007/05/14 A New Service Guideline for the Inspection and Replacement of the Flexible Mounts is Now Available on Soil Compactors and Paving Compactors {5654, 6605, 6606, 6607}
CP-533E and CS-533E Vibratory Soil Compactors Sound Information and Vibration Information
2007/07/16 Managing the Life Cycles of Excavator Final Drives {4050}
450E Backhoe Loader Engine Supplement Fan Drive - Remove and Install
2007/04/30 100% Leak Testing of Oil Coolers {1378}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Propel Cable - Remove and Install
AccuGrade® GPS (CD700) Designs
2007/06/04 Improvements to the Water Lines Groups {1380}
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Breaker Relief Valve
AccuGrade® GPS (CD700) Level Surface Design
2007/04/30 An Improved Starting Motor is Now Available {1453}
160M Motor Grader Engine Supplement Engine Enclosure (Hood) - Remove
160M Motor Grader Engine Supplement Engine Enclosure (Hood) - Install
AccuGrade® GPS (CD700) Sloping Surface Design
AP655D Asphalt Paver Engine Starting
587R Pipelayer Power Train Final Drive, Steering Clutch and Brake - Remove
The Hydraulic Float Function For the Three-Point Hitch is Causing Poor Actuation.{5051, 5702, 5705} The Hydraulic Float Function For the Three-Point Hitch is Causing Poor Actuation.{5051, 5702, 5705}