Customer Specified Parameters Table
Show/hide table
Customer Specified Parameters     | ||
---|---|---|
ECM Parameter     | Possible Values     | Default Value     |
Engine Rating Parameter     | ||
"Rating Number"     | 1 to 4     | 1     |
Low/High Idle Parameters     | ||
"Low Idle Speed"     | 700 to 1200 rpm     | 750 rpm     |
"High Idle Speed"     | 1900 to 2900 rpm     | 2650 rpm     |
ECM Identification Parameter     | ||
"Equipment ID"     | 17 Digits Available characters are dependent on the service tool that is used     |
Not Programmed     |
PTO and Throttle Lock Parameters     | ||
"Throttle Lock Feature Installation Status"     | Installed Not Installed     |
Not Installed     |
"PTO Engine Speed Setting"     | 0 to 3000 rpm     | 0 rpm     |
"Throttle Lock Increment Speed Ramp Rate"     | 0 to 600 rpm/sec     | 400 rpm/sec     |
"Throttle Lock Engine Set Speed Increment"     | 0 to 200 rpm     | 10 rpm     |
Miscellaneous     | ||
"Monitoring Mode Shutdowns"     | Disabled Enabled     |
Disabled     |
"Monitoring Mode Derates"     | Disabled Enabled     |
Enabled     |
"Limp Home Desired Engine Speed"     | 700 to 1800 rpm     | 1200 rpm     |
J1939 Continuous Fault Handling     | ||
"Remote Torque Speed Control Enable Status"     | Disabled Enabled     |
Disabled     |
Configurable Inputs     | ||
"Coolant Level Sensor"     | Not Installed Installed     |
Not Installed     |
"Air Filter Restriction Switch Installation Status"     | Not Installed Installed     |
Not Installed     |
"Fuel/Water Separator Switch Installation Status"     | Not Installed Installed     |
Not Installed     |
"User Defined Switch Installation Status"     | Not Installed Installed     |
Not Installed     |
Caterpillar Information System:
R1600G Load Haul Dump Machine Systems Control Valve (Wheel Steering) - Assemble
R1600G Load Haul Dump Machine Systems Control Valve (Wheel Steering) - Disassemble
R1600G Load Haul Dump Machine Systems System Pressure - Release
R1600G Load Haul Dump Machine Systems Steering Metering Pump - Install
R1600G Load Haul Dump Machine Systems Steering Metering Pump - Remove
R1600G Load Haul Dump Machine Systems Pilot Control Valve - Install
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System MID 082 - CID 2328 - FMI 06
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System MID 082 - CID 2328 - FMI 05
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System MID 082 - CID 2328 - FMI 03
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Control Valve (Backhoe Bucket)(Mechanically Operated)
541, 551 and 552 Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw)
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System MID 082 - CID 2326 - FMI 06
Installing the 258-3915, 294-5580 Work Tool Positioner Kit (SELF-LEVELING HYDRAULICS){1435, 5057, 5112, 5264, 5479} Installing the 258-3915, 294-5580 Work Tool Positioner Kit (SELF-LEVELING HYDRAULICS){1435, 5057, 5112, 5264, 5479}
Installing the 258-4127 Work Tool Wiring Kit {1408} Installing the 258-4127 Work Tool Wiring Kit {1408}
3500 Engines for Caterpillar Built Machines Turbocharger
793D Off-Highway Truck Power Train Gear Pump (Rear Axle Oil)
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Control Valve (Swing)(Mechanically Operated)
AP1055D and BG2455D Asphalt Pavers Engine Supplement Gear Pump (Fan Drive) - Remove
AP1000D and BG260D Asphalt Pavers Engine Supplement Control Valve (Fan Drive) - Remove and Install
AP1000D and BG260D Asphalt Pavers Engine Supplement Fan - Remove and Install
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Control Valve (Boom)(Mechanically Operated)
3500 Engines for Caterpillar Built Machines Turbocharger
793D Off-Highway Truck Power Train Differential and Bevel Gear
414E, 416E, 420E and 430E Backhoe Loaders Axles, Differential and Brakes Switch (Differential Lock)