Gear Pump (Fan Drive) - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1861     | Retaining Ring Pliers     | 1     |
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Install thrust plate (17) in housing (7) .
Show/hide table
Illustration 1 | g01139168 |
- Install seal (16) and use Tooling (A) to install retaining ring (15) in end cover (10) .
Show/hide table
Illustration 2 | g01139126 |
- Install seal (13) and backup ring (14) in end cover (10) .
Show/hide table
Illustration 3 | g01139118 |
- Install O-ring seal (12) in end cover (10) .
- Install end cover (10) and bolts (11) in housing (7) .
Show/hide table
Illustration 4 | g01139106 |
- Install driven gear (9) and drive gear (8) in housing (7) .
Show/hide table
Illustration 5 | g01139086 |
- Install thrust plate (6) in housing (7) .
Show/hide table
Illustration 6 | g01139062 |
- Install seal (4) and backup ring (5) in end cover (2) .
Show/hide table
Illustration 7 | g01139055 |
- Install O-ring seal (3) in end cover (2) .
- Install end cover (2) and nuts (1) .
Show/hide table
Illustration 8 | g01139019 |
End By: Install the fan drive gear pump. Refer to Disassembly and Assembly, "Gear Pump (Fan Drive) - Install".
Caterpillar Information System:
C9 Engine for Caterpillar Built Machines System Configuration Parameters
Installing the 266-9184 Cab Heater and Mounting Kit {7304} Installing the 266-9184 Cab Heater and Mounting Kit {7304}
Topcon® System Five General Hazard Information
C27 and C32 Engines for Caterpillar Built Machines E361 High Engine Coolant Temperature
539 Knuckleboom Loader Reference Material
994F Wheel Loader Bucket Wear Plates - Inspect/Replace
740 and 740 EJECTOR Articulated Trucks Power Train Power Train Hydraulic System
AP1055D and BG2455D Asphalt Pavers Engine Supplement Gear Pump (Fan Drive) - Disassemble
2005/01/31 Oversized Valve Guides are Available {1104}
2005/01/31 Oversized Valve Guides are Available {1104}
2005/01/24 Damaged Lifter Bores In 3400 Series Engines Can Be Used Again {1201}
539 Knuckleboom Loader Fuel System Secondary Filter Number One - Replace
C7 Engine for AP-1000D, AP-1055D, BG-2455D, and BG-260D Asphalt Pavers E362 Engine Overspeed
2005/04/11 A Special instruction, REHS2561, "Field Installation of the 255-7115 Equalizer Bar As " Is Available {7206}
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Piston Pump (Saw) - Remove
Oil Volumes for Track Link Assemblies {4169} Oil Volumes for Track Link Assemblies {4169}
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Piston Pump (Saw) - Install
R2900G Load Haul Dump Bucket Control Group Safety Pins
R2900G Load Haul Dump Braking System Parking Brake - Manual Release
R2900G Load Haul Dump Starting the Engine
R2900G Load Haul Dump Engine and Machine Warm-Up
R2900G Load Haul Dump Braking System Pressure Switch (Service Brake Oil)
R2900G Load Haul Dump Stopping the Machine
C11 and C15 Engines for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test