Engine - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 2     |
- Attach a suitable lifting device and Tooling (A) to engine (33). Install the engine in the machine and bolts (37) on both sides of the engine. The weight of the engine is approximately 333 kg (735 lb).
Show/hide table
Illustration 1 | g01081863 |
- Install support bracket (35), bolts (34), and bolt (37) .
Show/hide table
Illustration 2 | g01081775 |
- Remove the suitable lifting device and Tooling (A) from engine (33) .
Show/hide table
Illustration 3 | g01081774 |
- Reposition bracket (31) and install bolts (30). Remove the suitable blocking from piston pump (32) .
Show/hide table
Illustration 4 | g01081757 |
- Connect hose (29) and tighten clamp (28) .
Show/hide table
Illustration 5 | g01081756 |
- Reposition cable assembly (23) and tighten jam nut (25) .
Show/hide table
Illustration 6 | g01081705 |
- Install bracket (27) and bolt (26) .
- Reposition cable assembly (23) and install bolt (24) .
Show/hide table
Illustration 7 | g01081703 |
- Reposition harness assembly (19) and install clamp (20) and the bolt.
Show/hide table
Illustration 8 | g01081702 |
- Connect hose (22) and tighten clamp (21) .
- Reposition harness assembly (19). Connect harness assembly (18) .
Show/hide table
Illustration 9 | g01081690 |
- Connect harness assembly (17) .
Show/hide table
Illustration 10 | g01081362 |
- Reposition harness assembly (16) and install clamps (15). Connect harness assemblies (14) .
Show/hide table
Illustration 11 | g01081359 |
- Connect harness assemblies (12) on alternator (13) .
Show/hide table
Illustration 12 | g01081507 |
- Connect cable assemblies (10) on electric starting motor (11) .
Show/hide table
Illustration 13 | g01081505 |
- Install the gasket, exhaust pipe (9) and bolts (8) .
Show/hide table
Illustration 14 | g01081357 |
- Connect hose (6) on the engine and tighten clamp (7) .
Show/hide table
Illustration 15 | g01081146 |
- Connect hose (5) on the engine and tighten clamp (4) .
- Install guard (3) and bolts (2) .
Show/hide table
Illustration 16 | g01081143 |
- Connect battery ground cable (1) on the battery and tighten the clamp.
Show/hide table
Illustration 17 | g00610382 |
- Fill the engine and the radiator with coolant. Refer to Operation and Maintenance Manual for the correct procedure.
End By: Install the engine hood. Refer to Disassembly and Assembly, "Engine Hood - Remove and Install".
Caterpillar Information System:
446D Backhoe Loader Power Train Rear Axle - Install
CB-334E and CB-335E Vibratory Compactors Machine Systems Drive Shaft - Remove and Install
446D Backhoe Loader Engine Supplement Refrigerant Condenser - Remove and Install
446D Backhoe Loader Power Train Rear Axle - Remove
446D Backhoe Loader Engine Supplement Fuel Filter and Base - Remove and Install
988H Wheel Loader Machine Systems Evaporator Coil and Heater Coil - Remove
Installation Guide for the Machine Security System on Skid Steer Loaders and Multi Terrain Loaders{7631} Installation Guide for the Machine Security System on Skid Steer Loaders and Multi Terrain Loaders{7631}
446D Backhoe Loader Power Train Drive Shaft (Rear) - Remove and Install
797B Off-Highway Truck Engine Components - Rebuild//Replace/Install Reman - 797B LAA Machines Only
AP-800D and BG-230D Asphalt Pavers Machine Systems Gear Motor (Ventilation)
446D Backhoe Loader Power Train Drive Shaft (Front) - Remove and Install
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Refrigerant Condenser - Remove and Install
988H Wheel Loader Machine Systems Evaporator Coil and Heater Coil - Install
CP-323C and CS-323C Paving Compactors Machine Systems Wheel and Tire - Remove and Install
R2900G Load Haul Dump Machine Systems Accumulator Charging Valve (Brake) - Remove
R2900G Load Haul Dump Machine Systems Accumulator Charging Valve (Brake) - Install
2004/06/21 Special Instruction, REHS2149, "Explanation of Common Event Codes and Transmission Shift Matrix" is now Available {4800, 4808}
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Machine Systems Front Frame from Rear Frame - Separate
446D Backhoe Loader Power Train Tie Rod (Steering)(Front) - Remove and Install
2004/07/01 Engines Are Now Built with Semi-Crowned Lifter Rollers {1209}
446D Backhoe Loader Power Train Steering Cylinder (Front) - Remove and Install
2004/07/05 Improved Analysis of Non-Warrantable Failures for Reman Vane Cartridges {5055}
988H Wheel Loader Power Train Engagement Pressure for the Transmission Clutch (Operator Monitor) - Calibrate
446D Backhoe Loader Power Train Drive and Steering Axle (Front) - Remove