Rear Axle - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1U-7505 | Hydraulic Jack | 1 |
| ZZ | 6V-9508 | Plug | 2 |
| 6V-9829 | Cap As | 2 | |
Start By:
- Remove the rear tires. Refer to Disassembly and Assembly, "Tire and Rim (Rear) - Remove and Install".
- Remove the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) - Remove and Install".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Disconnect parking brake linkage (1) .
Show/hide table
 | |
| Illustration 1 | g01081868 |
- Remove bolt (3) in order to disconnect differential lock linkage (2) .
- Disconnect hose assembly (4). Repeat for the other side.
Show/hide table
 | |
| Illustration 2 | g01081869 |
- Install Tooling (A) under rear axle (7) .
Show/hide table
 | |
| Illustration 3 | g01081870 |
- Remove bolts (5) and plate (6). Repeat for the other side.
- Use Tooling (A) in order to remove rear axle (7). The weight of rear axle (7) is approximately 635 kg (1400 lb).
Caterpillar Information System:
446D Backhoe Loader Engine Supplement Fuel Filter and Base - Remove and Install
988H Wheel Loader Machine Systems Evaporator Coil and Heater Coil - Remove
Installation Guide for the Machine Security System on Skid Steer Loaders and Multi Terrain Loaders{7631} Installation Guide for the Machine Security System on Skid Steer Loaders and Multi Terrain Loaders{7631}
446D Backhoe Loader Power Train Drive Shaft (Rear) - Remove and Install
797B Off-Highway Truck Engine Components - Rebuild//Replace/Install Reman - 797B LAA Machines Only
AP-800D and BG-230D Asphalt Pavers Machine Systems Gear Motor (Ventilation)
446D Backhoe Loader Power Train Drive Shaft (Front) - Remove and Install
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Refrigerant Condenser - Remove and Install
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Refrigerant Compressor - Remove and Install
2004/06/28 Special Publications on Multi Terrain Loader Undercarriages Are Now Available {4150}
988H Wheel Loader Machine Systems Blower Motor (Air Conditioner, Heater) - Install
446D Backhoe Loader Power Train Parking Brake - Remove and Install
446D Backhoe Loader Engine Supplement Refrigerant Condenser - Remove and Install
CB-334E and CB-335E Vibratory Compactors Machine Systems Drive Shaft - Remove and Install
446D Backhoe Loader Power Train Rear Axle - Install
CB-334E and CB-335E Vibratory Compactors Engine Supplement Engine - Install
988H Wheel Loader Machine Systems Evaporator Coil and Heater Coil - Install
CP-323C and CS-323C Paving Compactors Machine Systems Wheel and Tire - Remove and Install
R2900G Load Haul Dump Machine Systems Accumulator Charging Valve (Brake) - Remove
R2900G Load Haul Dump Machine Systems Accumulator Charging Valve (Brake) - Install
2004/06/21 Special Instruction, REHS2149, "Explanation of Common Event Codes and Transmission Shift Matrix" is now Available {4800, 4808}
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Machine Systems Front Frame from Rear Frame - Separate
446D Backhoe Loader Power Train Tie Rod (Steering)(Front) - Remove and Install
2004/07/01 Engines Are Now Built with Semi-Crowned Lifter Rollers {1209}