Blade Cylinder Check Valve May Fail on Certain 300.9D Mini Hydraulic Excavators {5362, 7562}
- Mini Hydraulic Excavator
- 300.9D (S/N: DW21-UP; LJ21-UP; LJM1-UP; TGP1-UP)
Reference: "Testing and Adjusting", UENR0478
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified.
Problem
The blade cylinder check valve may fail on certain 300.9D mini hydraulic excavators. If the blade cylinder check valve fails, it will restrict hydraulic fluid from exiting the blade cylinder. The restriction may cause slow or intermittent function of the blade cylinder, or stop functioning completely.
Solution
Show/hide table
Required Parts | ||
---|---|---|
Qty | Part Number | Part Name |
1 | Blade Cylinder Gp | |
1 | Check Valve |
In the event of a failure, replace with the same part number.
Caterpillar Information System:
140 GC Motor Grader Systems Control Manifold (Brake)
Turbocharger Boost Pressure on Certain C4.4 Machine Engines {1052, 7432} Turbocharger Boost Pressure on Certain C4.4 Machine Engines {1052, 7432}
798 AC Off-Highway Truck Field Assembly Tire and Rim - Install
140 GC Motor Grader Systems Brake Control Valve (Service) - Check
Installation of Wheel Chock Kits on Certain 700 Series Articulated Trucks {7192} Installation of Wheel Chock Kits on Certain 700 Series Articulated Trucks {7192}
140 GC Motor Grader Systems Machine Preparation
Hydraulic Thumbs Decommissioning and Disposal
140 GC Motor Grader Systems Parking Brake - Test
798 AC Off-Highway Truck Field Assembly Air Lines (Turbocharger) - Install
140 GC Motor Grader Systems Hydraulic System
349, 352 Hydraulic Excavator Engine Supplement Diesel Exhaust Fluid Tank - Install
140 GC Motor Grader Systems Axle Toe-In (Front) - Adjust
Verify the Swing Relief Pressure When Replacing the Swing Motor on Certain 301.4C and 301.7D CR Mini Hydraulic Excavators {5058, 7051} Verify the Swing Relief Pressure When Replacing the Swing Motor on Certain 301.4C and 301.7D CR Mini Hydraulic Excavators {5058, 7051}
349, 352 Hydraulic Excavator Engine Supplement Temperature Sensor (DPF) - Remove
C18 Generator Set Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
Boom, Stick, Bucket, and Blade Hydraulic Cylinders May Leak on Certain 303.5E2, 304E2, and 304.5E2 Mini Hydraulic Excavators {5113, 5456, 5457, 5458} Boom, Stick, Bucket, and Blade Hydraulic Cylinders May Leak on Certain 303.5E2, 304E2, and 304.5E2 Mini Hydraulic Excavators {5113, 5456, 5457, 5458}
349, 352 Hydraulic Excavator Engine Supplement Fan - Install
C18 Generator Set Engine Oil and Filter - Change
349, 352 Hydraulic Excavator Engine Supplement Fan Motor - Install
C18 Generator Set Plate Locations and Film Locations
C18 Generator Set Model View Illustrations
The Planetary Gear and Pinion of Swing Drive Group May Fail on Certain M314F, M315D2, and M317D2 Wheeled Excavators {5459} The Planetary Gear and Pinion of Swing Drive Group May Fail on Certain M314F, M315D2, and M317D2 Wheeled Excavators {5459}
140 GC Motor Grader Systems Transmission Charge Pump
New Machine Software and EC520 Controller Monitor Software Is Now Available for Certain Excavators {7490, 7601, 7610, 7620} New Machine Software and EC520 Controller Monitor Software Is Now Available for Certain Excavators {7490, 7601, 7610, 7620}