Camshaft - Disassemble
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件名称 | 数量 |
| A | 1P-2320 | 组合式拉拔器 | 1 |
开始:
- 拆下凸轮轴组件。 请参阅拆解和组装, "凸轮轴 - 拆卸"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将齿轮 (5) 从凸轮轴 (1) 上拆下。
注: 应将齿轮放在一个合适的支架上，以防止在拆解过程中损坏调速器飞锤。
- 将垫片 (4) 和月牙键 (2) 从凸轮轴 (1) 上拆下。
- 使用工具 (A) 将轴承 (3) 从凸轮轴 (1) 上拆下。
注: 确定轴承的方位，以方便安装。
Show/hide table
| |
| 图 1 | g01326129 |
|
典型示例 | |
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C13 On-highway Engine Air Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 40 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 14 Amp and 15 Amp Alternators
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Line - Remove and Install
C13 On-highway Engine Air Lines
G3520C and G3520E Generator Set Engines Turbocharger Turbine Temperature Is Low
G3520C and G3520E Generator Set Engines Oil Filter Differential Pressure Problem
G3520C and G3520E Generator Set Engines Engine Stalls Immediately After Starting
G3520C and G3520E Generator Set Engines Engine Shutdown Is Intermittent
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Connecting Rod Bearings - Install - Connecting rods in position
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C0.5 and C0.7 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
G3520C and G3520E Generator Set Engines Turbocharger Compressor Bypass - Test
G3520C and G3520E Generator Set Engines Detonation - Test
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test
G3520C and G3520E Generator Set Engines Electrical Power Supply - Test