Cylinder Drift - Check
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools     | |
---|---|
Description     | Qty     |
Tape Measure     | 1     |
Stopwatch     | 1     |
Test Procedure for Boom, Stick, and Bucket Cylinders
Show/hide table
Illustration 1 | g00816216 |
- Start the engine.
- Position the machine on level ground.
- Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
- Load the bucket.
Weight of bucket load ... 105 kg (231.5 lb)
- Fully extend the bucket cylinder. Retract the bucket cylinder 10 mm (0.4 inch) from the fully extended state.
- Fully retract the stick cylinder. Extend the stick cylinder 10 mm (0.4 inch) from the fully retracted state.
- Raise or lower the boom until the bucket to stick pin is the same height as the boom foot pin. Refer to Illustration 1.
- Measure each cylinder's length from cylinder pin to cylinder pin.
- Stop the engine.
- Leave the machine in this position for three minutes. Measure each cylinder's length from cylinder pin to cylinder pin for drift.
Show/hide table
Cylinder Drift     | |
---|---|
Item     | Specification     |
Boom Cylinder     | 10 mm (0.39 inch) or less     |
Stick Cylinder     | |
Bucket Cylinder     | 5 mm (0.2 inch) or less     |
Test Procedure for Blade Cylinder
Show/hide table
Illustration 2 | g00816222 |
- Start the engine.
- Position the machine on level ground.
- Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
- Position the stick so that the stick is perpendicular to the ground. Lower the stick to the ground. Refer to Illustration 2.
- Fully retract the blade cylinder. Extend the blade cylinder 10 mm (0.4 inch) from the fully retracted state.
- Measure the blade cylinder's length from cylinder pin to cylinder pin.
- Stop the engine.
- Leave the machine in this position for three minutes. Measure the blade cylinder's length from cylinder pin to cylinder pin for drift.
Show/hide table
Cylinder Drift     | |
---|---|
Item     | Specification     |
Blade Cylinder     | 3 mm (0.12 inch) or less     |
Caterpillar Information System:
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System Visual Inspection
302.5C Mini Hydraulic Excavator Hydraulic System Cylinder Speed - Check
302.5C Mini Hydraulic Excavator Hydraulic System Travel on Level Ground - Test
302.5C Mini Hydraulic Excavator Hydraulic System Engine Performance - Test - Engine Speed
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System General Testing and Adjusting Information
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Hydraulic System Pressure - Release
302.5C Mini Hydraulic Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
302.5C Mini Hydraulic Excavator Hydraulic System Machine Drift on a Slope - Check
302.5C Mini Hydraulic Excavator Hydraulic System Main Hydraulic Pump Air - Purge
302.5C Mini Hydraulic Excavator Hydraulic System Operational Checks
302.5C Mini Hydraulic Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
302.5C Mini Hydraulic Excavator Hydraulic System Relief Valve (Line) - Test and Adjust
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Accumulator (Pilot) - Test and Charge
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Engine - Install
C18 Generator Sets Cooling System Supplemental Coolant Additive (SCA) - Test/Add
390D Excavator Machine Systems Actuator Motor (Air Distributor) - Remove and Install
390D Excavator Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Heater Core - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Heater Core - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Evaporator Coil - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Evaporator Coil - Install
390D Excavator Machine Systems Coolant Temperature Sensor - Remove and Install
390D Excavator Machine Systems Temperature Sensor (Cab Air) - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Pressure Switch (Refrigerant Pressure Cutoff) - Remove and Install