Pressure Switch (Refrigerant Pressure Cutoff) - Remove and Install
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
接触制冷剂会使人受伤。 接触制冷剂会造成冻伤。 让手、脸避开,有助于防止受伤。 制冷管路被打开时,即使压力计显示系统中已经没有制冷剂,也要始终戴着护目镜。 拆卸管件时,务必小心谨慎。 慢慢地拧松接头。 如果系统内仍有压力,就要把它缓慢地释放到一个通风良好的地方去。 通过燃着的香烟吸入制冷剂会使人受伤或死亡。 通过燃着的香烟或其他抽烟方法吸入空调制冷气体,或者,吸入空调制冷气体接触明火而形成的烟雾,都会造成对人体的伤害 或死亡。 维修空调时,或者,在任何可能存在制冷气体的地方都不要抽烟。 采用经过认可的回收和循环利用车妥善地从空调器中取出制冷剂。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 回收空调系统中的空调制冷剂。 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 请参阅专门出版物, NEDG5065, "空调工具"了解正确工具信息。
Show/hide table
图 1 g01187630 为了显示防护罩的位置而翻转了上部机架。 - 卸下挡板 (1)。
Show/hide table
图 2 g01187642 - 断开线束组件 (2)。
- 拆下压力开关 (3)。
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 安装压力开关 (3)。
- 连接线束组件 (2)。
Show/hide table
图 4 g01187630 为了显示防护罩的位置而翻转了上部机架。 - 安装挡板 (1)。
- 加注空调系统。 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 请参阅专门出版物, NEDG5065, "空调工具"了解正确工具信息。
Show/hide table
图 3 | g01187642 |
Caterpillar Information System:
390D Excavator Machine Systems Temperature Sensor (Cab Air) - Remove and Install
390D Excavator Machine Systems Coolant Temperature Sensor - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Evaporator Coil - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Evaporator Coil - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Heater Core - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Heater Core - Remove
390D Excavator Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
390D Excavator Machine Systems Actuator Motor (Air Distributor) - Remove and Install
C18 Generator Sets Cooling System Supplemental Coolant Additive (SCA) - Test/Add
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Engine - Install
303C CR and 303.5C CR Mini Hydraulic Excavators Hydraulic System Accumulator (Pilot) - Test and Charge
302.5C Mini Hydraulic Excavator Hydraulic System Cylinder Drift - Check
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Control Module (Automatic Temperature Control Unit) - Remove and Install
390D Excavator Machine Systems Temperature Sensor (Evaporator Coil) - Remove and Install
365C Excavator Machine Systems Temperature Sensor (Ambient Air) - Remove and Install
365C Excavator Machine Systems Heating and Air Conditioning Unit - Remove
365C Excavator Machine Systems Heating and Air Conditioning Unit - Install
M318C and M322C Excavators Machine Systems Upper Frame and Undercarriage Frame - Separate
M318C and M322C Excavators Machine Systems Upper Frame and Undercarriage Frame - Connect
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Alternator - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Pressure
302.5C Mini Hydraulic Excavator Machine Systems Boom - Remove and Install
325C Excavator Engine Supplement Engine Oil Cooler - Remove and Install
325C Excavator Engine Supplement Crankshaft Vibration Damper and Pulley - Remove and Install