Engine Oil Level - Check
Show/hide table
熱機油和高溫組件會導致人員受傷。 請勿讓熱油或發熱的組件接觸到皮膚。 |
Show/hide table
注意事項 |
---|
不可向曲軸箱中加油過滿。 否則會使引擎受損。 |
附註此機器配備同時檢查液位和油位尺的自動功能。 有關自動系統的資訊,請參閱操作及維護手冊, "監控系統"。 如果機器在斜坡上或僅將引擎停止一小段時間,則引擎機油不會流回曲軸箱,也無法透過上述兩種方法來正確檢查液位。 將機器停放在水平面上,在引擎至少停止 30 分鐘後檢查油位。
在引擎關閉時查看油位。 切勿在引擎運轉時檢查油位。
- 打開引擎蓋。
Show/hide table
插圖 1 g01172396 - 取下油尺。 擦掉油位尺上的油,並重新插入量桿。
Show/hide table
插圖 2 g00832222 - 取出並檢查油位尺。 油位應該介於 "FULL" (滿) 標記與 "ADD" (添加) 標記之間。
Show/hide table
注意事項 不要超過油尺上的"滿位 (FULL) "標記。
如果機油油位超過"滿位 (FULL) " 標記,則引擎操作過程中曲軸可能會浸入機油。這將導致機油溫度過高。 機油溫度過高會降低其潤滑特質。
Show/hide table插圖 3 g01172400 附註請參閱操作及維護手冊, "一般危險事項"部分,以瞭解盛裝溢放液體的資訊。
- 如有需要,請取出注油塞來加油。 請參閱操作及維護手冊, "潤滑黏度"。
附註如果油已變質或嚴重污染,請更換油 (不考慮維護週期)。
- 清潔注油塞。 裝上注油塞。
- 蓋上引擎蓋。
Caterpillar Information System:
M318C and M322C Excavators Machine Systems Gear Motor (Hydraulic Generator) - Assemble
M318C and M322C Excavators Machine Systems Gear Motor (Hydraulic Generator) - Disassemble
330D and 336D Excavators Alternate Exit
M318C and M322C Excavators Machine Systems Swing Drive - Install
M318C and M322C Excavators Machine Systems Swing Drive - Remove
330D and 336D Excavators Plate Locations and Film Locations
M318C and M322C Excavators Machine Systems Swivel - Install
M318C and M322C Excavators Machine Systems Swivel - Remove
S320B, S325B, S340B, S365B and S385B Demolition and Scrap Shears Bushings - Lubricate
330D and 336D Excavators Boom/Stick/Bucket Combinations
320D Excavator Fuses - Replace
330D and 336D Excavators Specifications
323D Excavator Engine Oil Level - Check
C9.3 Engines for Caterpillar Built Machines Lubrication System
M318C and M322C Excavators Machine Systems Main Control Valve - Remove
M318C and M322C Excavators Machine Systems Main Control Valve - Install
M318C and M322C Excavators Machine Systems Main Control Valve - Disassemble
M318C and M322C Excavators Machine Systems Main Control Valve - Assemble
324D Excavator Hydraulic System Oil Filter (Return) - Case Drain Filter
330D and 336D Excavators Engine Oil and Filter - Change
325C LCR Excavator Machine Systems Heater Core - Remove
301.6C and 301.8C Mini Hydraulic Excavators Engine Supplement Hydraulic Oil Cooler - Remove and Install
325D and 329D Excavators Hydraulic System Gear Pump (Pilot)
301.6C and 301.8C Mini Hydraulic Excavators Engine Supplement Alternator - Remove and Install