Bucket Linkage - Remove and Install
Removal Procedure
Start By:
- Remove the bucket. Refer to Disassembly and Assembly, "Bucket - Remove and Install".
- Start the machine. Place the stick on the floor, as shown above. Remove two nuts (1) and bolt (2) .
Show/hide table
Illustration 1 | g00575193 |
- Remove pin (3) from the bucket cylinder with a brass punch.
Show/hide table
Illustration 2 | g00575203 |
- Remove two shims (4) and linkage brackets (5) .
- Remove two nuts (6) and bolt (7) .
Show/hide table
Illustration 3 | g00575239 |
- Remove pin (8) from the stick with a brass punch.
Show/hide table
Illustration 4 | g00575244 |
- Remove two shims (9) and linkage brackets (10) from the stick.
Installation Procedure
Note: Be sure that the pins and the pin bores are thoroughly clean prior to installation of the linkage brackets.
- Apply a thin coat of 1P-0808 Multipurpose Grease on the diameter of the pin bores and the pins.
Show/hide table
Illustration 5 | g00575244 |
- Position linkage brackets (10) and two shims (9) to the stick in order to install the pin (8) .
- Install bolt (7) and two nuts (6). Tighten nuts and the bolt.
Show/hide table
Illustration 6 | g00575239 |
- Position linkage brackets (5) and two shims (4) to the bucket cylinder in order to install the pin (3) .
Show/hide table
Illustration 7 | g00575203 |
- Install bolt (2) and two nuts (1) to the pin. Tighten nuts and the bolt.
Show/hide table
Illustration 8 | g00575193 |
End By: Install the bucket. Refer to Disassembly and Assembly, "Bucket - Remove and Install".
Caterpillar Information System:
302.5 Mini Hydraulic Excavator Machine Systems Bucket - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Blade Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Blade - Remove and Install
3054 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
M318 and M320 Excavators Machine Electronic Control System Sensors
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Install
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Remove
307B Excavator Supplement for 4M40 Engine Fuel Priming Pump - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Muffler - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Remove
302.5 Mini Hydraulic Excavator Machine Systems Bucket Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Stick Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Stick - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Boom Cylinder - Remove and Install
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Service Meter Mode
302.5 Mini Hydraulic Excavator Machine Systems Boom - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Boom Swing Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Counterweight - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Fuel Tank - Remove
302.5 Mini Hydraulic Excavator Machine Systems Fuel Tank - Install
302.5 Mini Hydraulic Excavator Machine Systems Seat - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Cab Heater - Remove and Install